manualshive.com logo in svg

Allied Telesis AT-MR420TR, Руководство по установке

Поделиться
Скачать
Allied Telesis AT-MR420TR Скачать руководство пользователя страница 60

Glossary

38

medium (coax cable) for data packet transmission. It provides for a level of error 
detection should that transmission be corrupted or impeded by contention for 
the transmission medium.

COAX SEGMENT—A segment of Ethernet cable that contains MAUs.

COAXIAL CABLE—A two-conductor (center conductor, shield system), 
concentric, constant impedance transmission line used as the trunk medium in 
the baseband system.

COAXIAL CABLE SEGMENT—A length of coaxial cable sections and coaxial 
connectors, terminated at each end in its characteristic impedance.

COLLISION—An unwanted condition that results from concurrent 
transmissions on the physical medium.

COMPATIBILITY INTERFACE—The MDI coaxial cable interface and the 
AUI branch cable interface, the two points at which hardware compatibility is 
defined to allow connection of independently designed and manufactured 
components to the baseband transmission system.

CROSSOVER—Wiring used when connecting a 10Base-T MAU to another 
10Base-T MAU or a 10Base-T hub to another 10Base-T hub. For example, one 
10Base-T MAU has the TD (Transmitted Data) pair on the same pins as 
another 10Base-T MAU. If pins were wired straight, there would be two 
transmitters on one pair and no receiver. As a solution, the crossover cable 
crosses the TD pair with the RD (Ready Data) pair, to connect the TD pins on 
one end to the RD pins at the other end.

D-SUB CONNECTOR—The AUI cable uses 15-pin D-sub connectors. “D” 
refers to the shape of the connector shell. Also called miniature D, DB15, or DIX 
connectors.

DATA COMMUNICATION EQUIPMENT (DCE)—In RS-232 specification, 
a module, such as a modem, for connecting a DTE to other equipment. A 
repeater connected to a terminal or workstation for Omega management use is 
wired as a DCE.

DATA TERMINAL EQUIPMENT (DTE)—In RS-232 specification, a module 
typically at the end of a segment (i.e., uninterrupted length of Ethernet cable). 
The DTE could be an Ethernet workstation, repeater or bridge.

DIX CONNECTOR—See D-Sub Connector

HEARTBEAT—See Signal Quality Error

HOUSE WIRING—House wiring is the existing wiring inside a building. This 
wiring generally originates from one or more wiring closets, such as a telephone 
room. Some older buildings may have wiring unsuitable for 10 megabit data 
rates. In these circumstances, it is recommended that the wiring be tested with 
a 10Base-T signal/wire tester.

MRx20TR(STP/UTP)_BookA  Page 38  Thursday, April 3, 1997  5:24 PM

Содержание AT-MR420TR









































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды