manualshive.com logo in svg

Allied Telesis AT-MR420TR, Руководство по установке

Поделиться
Скачать
Allied Telesis AT-MR420TR Скачать руководство пользователя страница 41

AT-MR420TR and AT-MR820TR Installation Guide

19

5.13 ns/meter. This cable internally consists of four shielded twisted 
pair wires with an overall shield and drain wire; a 15-pin D-shell male 
connector at one end and a 15-pin D-shell female connector at the other 
end. Cable impedance is nominally 78 

Ω

. The AUI cable typically 

connects a transceiver attached to a coaxial segment to a DTE 
(workstation).

BNC Port

10Base2 requires an RG58U, thin coaxial cable. This cable is a 10 
Mbits/sec baseband with 50

 Ω

 impedance. See Figure 10. Connected 

with BNC-series connectors, the maximum segment length is 185 
meters (606 ft.).

10Base2 (Thin) Ethernet. 

When configuring thin coax segments, IEEE 

802.3 specifications allow 30 or fewer MAUs per cable segment spaced 
at no less than 0.5 meter (1.64 ft.). The 10Base2 cable length cannot 
exceed 185 meters (606 ft.) per 10Base2 cable segment. The worst case 
propagation delay for a 185 meters (606 ft.) thin Ethernet segment is 
950.9 ns. The propagation delay for 10Base2 Ethernet cable is 5.14 ns/
meter. Both ends of the segment must be terminated with a 50

Ω

 

termination with a power rating of 0.5 watts or greater. The 
AT-MR420TR and AT-MR820TR repeaters provide internal 50

Ω 

terminator with a slide switch. Earth grounding of the segment shield 
is required at only one point on the cable.

Figure 10: BNC-T Connector

MRx20TR(STP/UTP)_BookA  Page 19  Thursday, April 3, 1997  5:24 PM

Содержание AT-MR420TR









































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды