manualshive.com logo in svg

Allied Telesis AT-MR420TR, Руководство по установке

Поделиться
Скачать
Allied Telesis AT-MR420TR Скачать руководство пользователя страница 33

AT-MR420TR and AT-MR820TR Installation Guide

11

  

Note

A data packet is too fast for the human eye to distinguish on 
an LED, therefore the LEDs will not reflect real-time activity. 
The repeater artificially stretches the LED on time for easier 
observation.

Figure 6: Port Indicators

Each RJ45 repeater port has two LEDs — LINK OK and Receive:

❑

LINK OK
— No light—Indicates typically a physical connection problem. 

The device at the other end of the cable may be powered off, 
the cable may be loose or disconnected, or the cable has been 
wired incorrectly. Check the crossover cable.

—  Green (Steady)—Indicates a valid link exists.

❑

Receive
—  Amber (Flashing)—Link is OK, port is not partitioned and 

there is activity on the port. Brief flashes indicate low traffic 
levels.

In short, port status LEDs show the functionality of the port. If the 
LINK OK status light is green and the Receive status is flashing 
amber, a signal is being received and the segment attached to the port 
is functional.

MRx20TR(STP/UTP)_BookA  Page 11  Thursday, April 3, 1997  5:24 PM

Содержание AT-MR420TR









































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды