Alliance Laundry Systems ZWC372-3059, Сервисная инструкция

Страница: 59 / 76

37987
57
Section 5 Service Procedures
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the washer before servicing.
• Never start the washer with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the washer is properly grounded.
W003
WARNING
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
p. Through Serial No. 9606029040 - Use a right
angle needle nose pliers and remove spring
from around lower transmission tube (located
inside brake assembly).
NOTE: Remove spring by turning in a
counterclockwise direction (looking at bottom end
of shaft).
IMPORTANT: When installing spring, make sure it
is inserted into groove in large splines of lower
transmission tube. Use spring tool, No. 242P4, for
installing spring.
NOTE: When reassembling, place a small amount
of lubricant to top side of drive pulley that will be
contacting large flat washer. Lubricate helix ramps
and bore with a small amount of lubricant. Refer to
Figure 42.
IMPORTANT: DO NOT OVER LUBRICATE!
Excess lubricant can be thrown into pivot dome
area during normal washer operation. Any
lubricant on the pivot dome or snubber pad and
isolator assembly will cause premature tripping of
the out-of-balance switch. This condition will
persist until lubricant is removed.
q. Remove three screws and rubber sleeves
holding brake pads to lower bearing housing.
Refer to Figure 42.
r. Lift brake assembly and pads off transmission
tube.
s. Remove three screws holding lower bearing
housing to tub support legs. Refer to Figure 42.
t. Rotate bearing housing past legs, then carefully
lift bearing housing off transmission tube.
NOTE: It may be necessary to loosen one leg from
outer tub to rotate bearing housing. Tap lightly on
housing to loosen it from transmission tube.
IMPORTANT: When installing lower bearing
housing, apply No. 27604P Anti-Seize Compound to
the area of transmission tube that will be contacting
bearing. Refer to Figure 43.
TO REMOVE BEARING
a. Support bearing housing around outside
diameter of bearing opening and carefully press
bearing out of the housing.
b. Clean all foreign material from inner diameter
of bearing opening.
c. Clean any foreign material from outside
diameter of new bearing.
d. Apply a retaining compound (such as Loctite)
to outside diameter of new bearing and
carefully press new bearing into housing (with
sealed side facing up).
IMPORTANT: Press new bearing into housing by
pressing on outer race of bearing only, and press
until bearing bottoms out in housing.
43. TRANSMISSION ASSEMBLY
a. Open loading door.
b. Remove agitator by placing two agitator hooks,
No. 254P4P, under bottom edge of agitator.
Refer to Figure 12.
IMPORTANT: Hooks should be positioned 180
degrees of each other, and must be placed under
agitator vane for greater stability. If hooks are
placed between vane area, damage to agitator may
occur.
c. Using a rocking motion (back and forth)
carefully lift agitator off drive bell.
d. Remove two screws from bottom edge of front
panel. Refer to Figure 20.
e. Pull bottom of panel away from washer until
hold-down clips (located on top flange of
panel) disengage from slots in cabinet top.
Refer to Figure 20.
f. Remove two cabinet top hold-down screws,
and hinge cabinet top or remove. Refer to
Paragraph 34.
g. Loosen hose clamp and disconnect filler hose
from outer tub cover. Refer to Figure 32.
NOTE: When reinstalling filler hose, the white line
or hose that connects to tub cover must be aligned
with line located on top side of outer tub cover.
Refer to Figure 32.