Alliance Laundry Systems HTEB17-N2802, Руководство по обслуживанию

Страница: 123 / 180

801774
121
Section 5 Service Procedures
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect all electric power to the machine and accessories before servicing.
• Close gas shut-off valve to gas dryer before servicing.
• Never start machine with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the machine is properly grounded.
• Washer motor not grounded! Disconnect electric power before servicing motor.
W502
WARNING
NOTE: To avoid damage to door seal, DO NOT use
pliers or sharp objects to grasp the door seal lip. If
lip is damaged, seal will leak.
h. Using a circular motion, pull seal up
( Figure 25 , Step 1 ), out ( Figure 25 , Step 2 ), and
down ( Figure 25 , Step 3 ).
i. When seal releases from lip of front panel, pull
out and remove the seal from front panel around
door opening. Refer to Figure 25 , Step 4 .
j. Working through the control panel opening,
remove two screws holding bottom flange of
control cabinet front to top flange of front
panel. Refer to Figure 17 .
k. While supporting the front panel assembly,
remove the two bottom front corner screws.
Refer to Figure 26 . Remove front panel (with
loading door attached) away from washer as far
as wires permit.
l. Unplug wire harness from both the door latch
switch and from the door switch. Refer to
Figure 29 . Remove clips holding wire harness
and door seal hose along top flange of front
panel and remove front panel.
NOTE: The large wire clip holds both the wire
harnesses and the door seal hose. Refer to
Figure 29 .
m. Loosen hose clamp and remove dispenser
valve-to-door seal hose connection at the
dispenser. Refer to Figure 29 .
IMPORTANT: When installing door seal hose, pull
hose tie tight to prevent damage. Refer to Figure 29 .
n. Loosen large clamp holding door seal to front
of outer tub. Carefully pull seal off front lip of
outer tub front panel and remove door seal and
hose. Refer to Figure 29 .
NOTE: Door seal installation can be improved
using water or soap solution to work seal around
circumference of loading door opening. Be sure to
install seal with the tab in the 12 o’clock position.
o. Disconnect ground wire from outer tub front
panel. Refer to Figure 32 .
p. Remove nut, washers and screw holding clamp
ring to outer tub front panel. Refer to Figure 32 .
q. Remove rubber seal from outer tub front panel
and discard seal.
IMPORTANT: Always replace seal with a new seal.
Spray or apply a mixture of diluted laundry
detergent to assist in installation of new seal. The
“puffy” side of seal should be installed to the inside.
For best results, tap clamp ring all around while
tightening screw and nut.
NOTE: Install metal clamp ring by placing clamp
ring opening at approximately the 10 o’clock
position to ensure that no interference is
encountered with side panel or the underside of the
control cabinet or cabinet top. Tighten the clamp
ring screw and nut until a spacing of one inch is
achieved at the clamp ring opening or until tight.
r. Run belt off pulley while slowly turning pulley.
Refer to Figure 22 .
s. Remove belt from motor shaft.
t. Remove cap screw (left hand thread),
lockwasher and flat washer holding pulley to
inner basket shaft. Refer to Figure 36 .
NOTE: Cap screw can be accessed through hole in
rear panel by removing hole plug. Refer to
Figure 36 .
u. Remove pulley front shaft.
IMPORTANT: When installing pulley, always use a
new cap screw to prevent screw from loosening
during operation. Use a 3/8 - 24 UNF left hand
thread tap to clean old Loctite out of pulley screw
receiving hole before installing new screw. This
ensures that inner basket and pulley properly seat.
NOTE: When installing new cap screw, apply a
thread locking compound to screw threads and
torque new cap screw to 240 minimum to 260
maximum inch pounds (27.5 to 29.7 Nm).