background image

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

70400001

1

Installation must conform with local codes or in the absence of local codes with:

In the U.S.A., installation must conform to the latest edition of the American National Standard Z223.1/
NFPA 54 “National Fuel Gas Code” and Standard ANSI/NFPA 70 “National Electric Code.”

In Canada, installation must comply with Standards CAN/CSA-B149.1 or Natural Gas and Propane Code 
CSA C22.1, latest edition, Canadian Electric Code, Part I.

In Australia, installation must comply with the Australian Gas Association Installation Code for Gas 
Burning Appliances and Equipment. 

IMPORTANT: Information must be obtained from a local gas supplier on instructions to be followed if the 
user smells gas. These instructions must be posted in a prominent location. Step-by-step instructions of the 
above safety information must be posted in a prominent location near the tumbler for customer use. 

FOR YOUR SAFETY, the information in this 
manual must be followed to minimize the 
risk of fire or explosion or to prevent 
property damage, personal injury or death.

W033

WARNING

• Do not store or use gasoline or other 

flammable vapors and liquids in the 
vicinity of this or any other appliance.

• WHAT TO DO IF YOU SMELL GAS:

– Do not try to light any appliance.
– Do not touch any electrical switch; do 

not use any phone in your building.

– Clear the room, building or area of all 

occupants.

– Immediately call your gas supplier from 

a neighbor’s phone. Follow the gas 
supplier’s instructions.

– If you cannot reach your gas supplier, 

call the fire department.

• Installation and service must be 

performed by a qualified installer, service 
agency or the gas supplier.

W052

FOR YOUR SAFETY

Do not store or use gasoline or other 
flammable vapors and liquids in the 
vicinity of this or any other appliance.

W053

POUR VOTRE SÉCURITÉ

Ne pas entreposer ou utiliser d’essence ou 
toutes autres vapeurs et liquides 
inflammables à proximité de cette unité ou 
de tout autre appareil.

W053R2QU

POUR VOTRE SÉCURITÉ, les informations 
de ce guide doivent être respectées afin de 
réduire les risques d’incendie, d’explosion 
ou d’éviter les dommages matériels, 
personnels ou blessures mortelles.

W033R3QU

MISE EN GARDE

• Ne pas entreposer ou utiliser d’essence 

ou toutes autres vapeurs et liquides 
inflammables à proximité de cette 
machine ou de tout autre appareil.

• QUE FAIRE EN CAS D’ODEUR DE GAZ :

– Ne pas mettre d’appareil en marche.
– Ne pas toucher aux interrupteurs 

électriques ; ne pas utiliser le 
téléphone des lieux.

– Évacuer la pièce, le bâtiment ou la zone 

de tous les occupants.

– Appeler immédiatement le fournisseur 

de gaz de la maison d’un voisin. 
Respecter les instructions 
communiquées par le fournisseur.

– Si vous ne pouvez pas joindre le 

fournisseur de gaz, appeler le service 
d’incendie.

• L’installation et l’entretien doivent être 

effectués par un installateur, service 
d’entretien qualifiés ou par le fournisseur 
de gaz.

W052R5QU

Содержание 25 Pound Capacity






























Отзывы: