background image

Operating Instructions

70400001

14

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

DMP Coin 

DV and DX Control Suffixes 
Description of The Coin Control Panel

Refer to 

Figure 6

.

 

TMB1955N

1

Clock Symbol. This symbol of a clock indicates that the time in the display is counting down to zero.

2

Display. Displays the drying time, cooling time, drying temperature, and diagnostics.

3

Hidden Keys. Used for programming in the coin mode – increases or decreases the value in the display. In 
conjunction with the START button, these buttons are used to adjust the drying time, cooling time, temperature, 
clockwise time, dwell time, counterclockwise time, and minutes per coin. 

4

Temperature LEDs. Indicate temperature setting.

5

DRYING LED. Illuminated when in the drying cycle.

6

INSTRUCTIONS. Instructions to start a drying cycle. 

7

COOLING LED. Illuminated when in the cooling cycle or when the display is currently showing the time for the 
cooling cycle.

8

START. Starts or resumes the current program or cycle

9

Temperature Select. This button toggles through the three temperature selections.

Figure 6 

DRYING

PERM. PRESS

COOLING

INSTRUCTIONS

START

TEMP

INSERT COIN (S)

SELECT TEMP.
PUSH START

1

2

3

HIGH

MINUTES

MEDIUM

LOW

TMB1955N

8

9

1

2

3

4

5

6

7

Содержание 25 Pound Capacity






























Отзывы: