allen MSP455 страница 45 Скачать руководство пользователя

Страница: 45 / 108

052793 - 03/2013

SECTION 3

SERVICE

Page 3-5

Engine Oil Maintenance

Engine Oil Level Check

• ALWAYS check the engine oil dipstick before using the riding trowel. At a minimum check engine oil

once per day. Follow the Maintenance and Lubrication Chart contained herein.

• ALWAYS use a good quality engine oil.

• The engine oil fill is the same as the oil dipstick hole and is located on the engine block opposite the

crankcase drain hose and plug.

• Use oil grades appropriate to the surrounding temperature range as shown below. See

GRADE OF

OIL CHART

under

CHANGING ENGINE OIL

section below.

• Remove engine oil dipstick to access oil fill hole. To fill engine with oil use a long funnel to avoid spill

ing or use an oil can filled with the proper weight small engine oil and squirt oil directly into fill hole.

Check oil level with dipstick. Fill the crank case to the full mark on the dipstick.

DO NOT

overfill.

• Replace dipstick.

Change Engine Oil

Important: Engine oil is best drained when the engine is warm. Warm oil flows

freely and carries away more impurities than cold oil.

Note:

Change engine oil every

25 hours

of operation. On a new engine, change oil after the first

hours

of operation.

Note:

Trowel must be on a level surface when changing and checking oil.

Note: Viscosities shown in the chart below may be used when the average temperature in your area

is within the indicated range.

• SAE 30 is recommended for general, all-temperature use (above 32°F (0°C)).

Содержание MSP455













































































































Результаты поиска

Содержание MSP455

Отзывы:

Похожие инструкции для MSP455

Бренды по названию

Популярные бренды

allen MSP455, Руководство по эксплуатации и запасным частям

Результаты поиска

Содержание MSP455

Отзывы:

Похожие инструкции для MSP455

Бренды по названию

Популярные бренды