allen MSP455 страница 35 Скачать руководство пользователя

Страница: 35 / 108

052793 - 03/2013

SECTION 2

OPERATIONS

Page 2-3

Pre-Operating Instructions - cont’d

Starting Procedures

Before starting riding trowel, refer to

gures below for location and identi

cation of opera tional and vi-

sual controls pertaining to the operation of the riding trowel.

Sit down correctly on the riding trowel seat. DO NOT attempt to start the riding trowel without

an operator in the seat.

If engine is cold, pull out the choke lever. Press down on throttle pedal (located by the opera-

tor’s right foot) one to two times.

To much throttle during start-up will

ood the engine.

Turn igintion switch key to the start-position, immediately release key when engine starts. If

after two or three attempts the engine has not started push in choke. Attempt to start trowel

again. Allow engine to warm up for 5 minutes before operating riding trowel.

Operating the starter for more than 5 seconds can damage the starter or engine. If engine fails to start

release the switch and wait 15 seconds before operating starter again.

Содержание MSP455













































































































Результаты поиска

Содержание MSP455

Отзывы:

Похожие инструкции для MSP455

Бренды по названию

Популярные бренды

allen MSP455, Руководство по эксплуатации и запасным частям

Результаты поиска

Содержание MSP455

Отзывы:

Похожие инструкции для MSP455

Бренды по названию

Популярные бренды