Allen-Bradley POINT I/O 1734-IB4D Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 24

background image

POINT I/O 24V DC 4-channel Discrete Input Module with Diagnostics

9

Publication 1734-IN029B-EN-E - July 2018

Install the Mounting Base

To install the mounting base on the DIN rail, proceed as follows:

1. Position the mounting base vertically above the installed units, for example,

adapter, power supply, or existing module.

2. Slide the mounting base down so that the interlocking side pieces engage the

adjacent module or adapter.

3. Press firmly to seat the mounting base on the DIN rail until the mounting base

snaps into place.

31586

Slide the mounting base until the
interlocking side pieces engage the
adjacent module or adapter.

«
...
7
8
9
10
11
...
»

Содержание POINT I/O 1734-IB4D

























Отзывы:

Нет отзывов

Похожие инструкции для POINT I/O 1734-IB4D

Бренд: Yamaha Страницы: 4

Бренд: Reliable Страницы: 6

NuDAQ cPCI-7248

Бренд: ADLINK Technology Страницы: 59

Star Celeste S140

Бренд: Tyco Fire Product Страницы: 4

Бренд: Lightspeed Страницы: 31

Бренд: Falco Страницы: 65

Бренд: XtendLan Страницы: 12

Бренд: LSS Страницы: 14

Бренд: Barnstead Thermolyne Corporation Страницы: 32

EASY CLEAR EQ-12-TH

Бренд: Bunn Страницы: 2

Бренд: WinSystems Страницы: 30

PressureMAT PMAT2

Бренд: PendoTECH Страницы: 48

Бренд: Net.Do Страницы: 35

Auto Sentry Petro

Бренд: ICS Страницы: 42

Бренд: RAM Страницы: 36

Weighing System

Бренд: NAUSICAA Страницы: 16

Бренд: Tynetec Страницы: 44

Бренд: M&S Systems Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды