manualshive.com logo in svg

Allen-Bradley POINT I/O 1734-IB4D, Руководство по установке

Поделиться
Скачать
Allen-Bradley POINT I/O 1734-IB4D Скачать руководство пользователя страница 18

18

    POINT I/O 24V DC 4-channel Discrete Input Module with Diagnostics 

Publication 1734-IN029B-EN-E - July 2018

Interpret the Indicators

See the figure and table that show how to interpret LED indicators.

1734-IB4D

Interpret LED Indicators Module Status

Indication

Probable Cause

Recommended Action

Module Status

Off

No power applied to device.

Apply power to device.

Green

Device operating normally.

None.

Flashing green

Device needs commissioning due to 
configuration missing, incomplete, 
or incorrect.

Configure device properly.

Flashing red

Recoverable fault.

1. Cycle power to device.
2. If condition persists, replace device.

Red

Unrecoverable fault may require 
device replacement.

Replace device.

Flashing red/green

Device is in self-test.

None.

Status of input 0 

Status of input 1 

Status of input 2 

Status of input 3 

Module status

Network status

44217

Содержание POINT I/O 1734-IB4D

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды