Allen-Bradley POINT I/O 1734-IB4D Скачать руководство пользователя страница 21

Страница: 21 / 24

POINT I/O 24V DC 4-channel Discrete Input Module with Diagnostics

Publication 1734-IN029B-EN-E - July 2018

Specifications

POINT I/O 24V DC 4-channel Digital Diagnostics Input Module – 1734-IB4D

Attribute

Value

Module location

1734-TB, 1734-TBS, 1734-TOP, and 1734-TOPS bases

POINTBus current, max

50 mA @ 5V DC

Power dissipation, max

0.6 W @ 28.8V DC

Thermal dissipation, max

1.9 BTU/hr @ 28.8V DC

Isolation voltage

50V DC (continuous), Reinforced insulation type
Tested at 1000V DC for 60 s, field-side to system

Field power bus
Supply voltage, nom
Voltage range

24V DC
10…28.8V DC

Dimensions HxWxL, approx.

56 x 12 x 75.5 mm (2.2 x 0.47 x 2.97 in.)

Terminal base screw torque

0.8 Nm (7 lb-in)

Keyswitch position

Weight, approx.

36 g (1.27 oz)

Reverse polarity protection

Yes

On-state voltage (Von), min

11V DC

On-state voltage (Von), max

28.8V DC (Vmax)

On-state current (Ion), min

2.0 mA

On-state current (Ion), max

15.0 mA (Imax)

Off-state voltage (Voff), min

-3V DC

Off-state voltage (Voff), max

5V DC

Off-state current (Ioff), max

1.5 mA

Input filter

Each input independently settable in 1 µs intervals (rounded to
nearest 333 µs).
Default value is 1000 µs.

Off to on filter, min

0 µs

Off to on filter, max

65 535 µs

On to off filter, min

0 µs

Off to on filter, max

65 535 µs

Содержание POINT I/O 1734-IB4D

























Результаты поиска

Содержание POINT I/O 1734-IB4D

Отзывы:

Бренды по названию

Популярные бренды

Allen-Bradley POINT I/O 1734-IB4D, Руководство по установке

Результаты поиска

Содержание POINT I/O 1734-IB4D

Отзывы:

Бренды по названию

Популярные бренды