manualshive.com logo in svg

Allen-Bradley FlexLogix 1794, Справочное руководство

Поделиться
Скачать
Allen-Bradley FlexLogix 1794 Скачать руководство пользователя страница 36

Publication 1794-RM001G-EN-P - December 2011

3-14

        FLEX I/O Modules

•

Wire Output Back to Input and Examination of Output Data 
Feedback signal:

 Users must wire an analog output to an actuator and 

then back to an analog input to monitor the output’s performance. (The 
use of feedback transmitters to verify an output’s performance is 
acceptable.) The application logic must examine the Data Feedback 
value associated with each output point to make sure that the requested 
output command from the controller was received by the module. The 
value must be compared to the analog input that is monitoring the 
output to make sure the value is in an acceptable range for the 
application.

In the ladder diagram in Figure 3.12, a user-defined percentage of 
acceptable deviation (that is, tolerance) is applied to the configured 
range of the analog input and output (that is, range) and the result is 
stored (that is, delta). This delta value is then added to and subtracted 
from the monitoring analog input channel; the results define an 
acceptable High and Low limit of deviation. The analog Output 
Feedback is then compared to these limits to determine if the output are 
working properly.

The output’s OK bit preconditions a Timer run that is preset to 
accommodate an acceptable fault response time and any communication 
filtering, or output, lags in the system. If the monitoring input value and 
the Output Feedback miscompare for longer than the preset value, a 
fault is registered with a corresponding alarm.

Figure 3.12 Monitoring an Analog Output with an Analog Input

The control, diagnostics and alarming functions must be performed in 
sequence.

Timer done

Timer

Outputs Faulted

Alarm to Operator

Outputs OK

ADD
Delta

Monitoring input

High Limit

MULT
Range
Tolerance %
Delta

Outputs Faulted

LIM
Low Limit
Output Echo
High Limit

Outputs OK

SUB
Delta

Monitoring input

Low Limit

Содержание FlexLogix 1794





























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды