manualshive.com logo in svg

Allen-Bradley ControlLogix DeviceNet, Руководство по установке, Страница: 8 / 10

Поделиться
Скачать
Allen-Bradley ControlLogix DeviceNet Скачать руководство пользователя страница 8

8

Rockwell Automation Publication 1756-IN065A-EN-P - September 2017

ControlLogix DeviceNet Scanner Module

Wire the DeviceNet Connector

Use an open-style 5- or 10-position linear plug to connect to the 
DeviceNet network. An open-style 10-position linear plug is provided 
with your module.

Wire the connector according to the following illustrations.

Connect the Module to the DeviceNet Network

Attach the connector to the module DeviceNet port as shown. 
Tighten the screws on the connector as needed.

IMPORTANT

For detailed DeviceNet connection information, see the 
DeviceNet Media Design and Installation Guide, publication 

DNET-UM072

.

Also see the Industrial Automation Wiring and Grounding 
Guidelines, publication 

1770-2.1

. 

Color Chips (dots)

Red Dot

Black Dot

Blue Dot

White Dot

10-position Plug

5-position Plug

20474-

D

D

D

D

D

Linear Plug

10-position

Drop Line or

DeviceNet

Trunk Cable

Red

White

Bare

Blue

Black

31716-M

10-position 
Linear Plug

DeviceNet Port 
Connector

DeviceNet Drop Line or Trunk 
Connector

Содержание ControlLogix DeviceNet











Отзывы:

Нет отзывов