2
WZ
3
16:2 / WZ
3
12:2 / WZ
3
20S
SYS-LINK Option Fitting Instructions AP5735
Fitting Instructions
Step 1:
Preparation
Ensure the console is powered off. Disconnect
the mains power lead and all connected cables.
Remove the console from its rack or other
furniture and place on the work surface.
Step 2:
Open the connector panel
Start by removing the side trims if fitted: four
M4x10 Pozi screws per side.
Remove the two M3x6 Torx screws from each
side of the connector panel. Remove the six
M3x6 Torx screws from the rear of the connector
panel. Carefully tilt the connector panel away
from the console so that it is flat on the work
surface.
Step 3:
Remove the blanking plate
Remove the two blanking plate screws from the
rear of the connector pod. Remove the
blanking plate.
Step 4:
Fit the SYS-LINK card
The SYS-LINK circuit card assembly is fixed to
the connector panel using two D-type connector
nuts. These are supplied already fitted to the
card’s socket. Remove the nuts and place the
card into the connector panel slot, observing the
correct orientation. Secure the SYS-LINK card
by refitting the D-type nuts, ensuring that they
are fully tightened.
Step 5:
Connect the SYS-LINK power
The option gets its power from the console
supply rails. Hand solder the SYS-LINK pcb
sleeved red, black and green wires to the
connector pcb: red to pin +15V, black to pin -
15V and green to pin SGND. Check that the
solder joints are of good quality.
Step 6:
Plug in the IDC harness
Plug one end of the supplied IDC harness into
header CN1 on the SYS-LINK card. Plug the
other end into the corresponding IDC header on
the connector card: CN7 on the WZ
3
16:2 and
WZ
3
20S or CN222 on the WZ
3
12:2.
Step 7:
Refit the connector panel
Check your work and ensure that there is no dirt
or debris inside the connector pod. Ensure that
all IDC harnesses are correctly inserted and
positioned. Carefully refit the connector panel
to the console, making sure not to trap and
possibly damage the SYS-LINK card’s IDC and
power harnesses. Replace the ten M3x6 Torx
screws - six at the rear of the connector panel
and two at each side. Refit the side trims if
required using the four M4x10 Pozi screws.
Step 8:
Test
With all panels refitted, connect to the mains
supply. Power on and check for correct
operation
CN1
CN7
IDC AND POWER HARNESS FITMENT - WZ³16:2 / WZ³20S
CN1
SGND
+15V
-15V
DGND
ALLEN&HEATH
SINGLE
INTERNAL
AUX5
AUX6
FX
EXTERNAL
-
R
EFFECT
EFFECT
DUAL
1-16
EFFECT
1-8
9-16
L/M
ST1
-
+
+
L
R
MIX
- IN
+IN
3
INPUT
2
1
RING -IN
RING
TIP +IN
TIP
LINE
MIC
LINE IN/OUT
TIP
RING
SEND
RETURN
XLR OUT
- OUT
3
2
1
INSERT
+OUT
TIP +
RING -
MIDI IN
FOOTSWITCH
FX MUTE
FX EDIT
MixWizard WZ
3
16:2
1
INSERT
2
1
MIC
LINE IN
OUT
DIRECT
3
INSERT
2
MIC
OUT
3
MIC
LINE IN
DIRECT
OUT
INSERT
DIRECT
LINE IN
4
INSERT
4
DIRECT
OUT
LINE IN
MIC
5
INSERT
6
5
LINE IN
MIC
DIRECT
OUT
BACKUP SUPPLY
REFER TO USER GUIDE FOR DETAILS.
ONLY USE RECOMMENDED ALLEN&HEATH POWER SUPPLY.
EXTERNAL DC IN
Serial No.
Made in the UK by ALLEN & HEATH Limited
OFF
0
I
ON
T630mA L 250V 20mm
FUSE
AC MAINS IN ~
100 - 240V~ 47-63Hz 45W MAX
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
REPLACE FUSE WITH SAME TYPE AND RATING.
CAUTION: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE
ATTENTION: REMPLACER LE FUSIBLE AVEC UN DES MEMES CARACTERISTIQUES.
DO NOT OPEN
CAUTION
RISK OF ELECTRIC SHOCK
AVIS: RISQUE DE CHOC ELECTRIQUE - NE PAS OUVRIR.
WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.
WARNING: THIS APPARATUS MUST BE EARTHED
INSERT
7
6
7
LINE IN
MIC
DIRECT
OUT
8
INSERT
8
DIRECT
OUT
LINE IN
MIC
INSERT
DIRECT
OUT
LINE IN
MIC
8
7
6
5
4
3
2
1
INSERT
10
9
LINE IN
MIC
DIRECT
OUT
11
INSERT
11
LINE IN
MIC
DIRECT
OUT
INSERT
10
DIRECT
OUT
LINE IN
MIC
12
13
INSERT
OUT
12
DIRECT
LINE IN
MIC
INSERT
14
13
MIC
LINE IN
OUT
DIRECT
14
MIC
OUT
15
INSERT
15
MIC
LINE IN
OUT
DIRECT
16
INSERT
16
MIC
LINE IN
OUT
DIRECT
L
R
L
R
INSERT
INSERT
DIRECT
LINE IN
1
SEND
2
AUX
3
AUX
AUX
AUX
AUX
5
AUX
IN
ST1
6
4
L
IN
R
L
/MONO
R
ST2
AB
A
B
SYS-LINK OUT ( option )
OUT
M
/MONO
16
15
14
13
12
11
10
9
9
REMOVE 6x M3 TORX SCREWS
REMOVE SIDE TRIMS
REMOVE 2x M3 TORX SCREWS PER SIDE
REMOVE 4x M4 POZI SCREWS PER SIDE
/MONO
M
OUT
SYS-LINK OUT ( option )
B
A
AB
ST2
R
/MONO
L
R
IN
L
ST1
IN
EXTERNAL
AUX6
AUX5
INTERNAL
INTERNAL
AUX5
AUX6
EXTERNAL
IN
ST1
L
IN
R
L
/MONO
R
ST2
AB
A
B
SYS-LINK OUT ( option )
OUT
M
/MONO
IDC AND POWER HARNESS FITMENT - WZ³12:2
CN222
CN1
CN1
RED
BLACK
GREEN
-15V
+15V
SGND
CN1
WZ
3
16:2 SHOWN,
OTHERS SIMILAR
