background image

 

 

KEG KIT INSTALLATION (cont.) 

 
3.  Remove the beer line access hole plug located on the inside of  the  refrigerator,  just  below  evaporator.           

(See pictures 3 & 4) 

4.  Insert the beer line (3/16” ID / clear color tubing) from the top of the refrigerator and allow it to drop to the inside of the 

refrigerated compartment. 

 
 

NOTE: 

The beer line travels through the back section of the unit into the refrigerated compartment by following the 

 

faucet arm support structure located behind the refrigerator’s back cover. (See pictures 5) 

 
 

There is no need to remove the back cover of the refrigerator for this procedure.

 

 
5.  Once the beer line has been inserted all the way to the refrigerated section, insert the support arm into the top opening. 
6.  Install the pressure regulator to the CO

2

 bottle and tighten securely using a wrench in order to avoid CO

2

 leakage.  

7.  Close the ball valve in the regulator and open the CO

2

 bottle valve.  

8.  Adjust the regulator to a pressure between 8 ~ 10 PSI using the regulator set screw.  
 
 

NOTE: 

More than 10 PSI of pressure will cause the beer to foam up at the tap, maintain the pressure between 

 

 8 ~ 10 PSI for optimum performance. 

 
9.  Connect the CO

2

 line (5/16” ID / Blue color tubing) to the regulator and Sanitary Key [SANKEY] and install the hose 

clamps provided in order to secure the tubing to the hose barbed fittings. 

10.  Install the Sanitary Key [SANKEY] on the beer keg and connect the beer line from the faucet arm to the SANKEY. Secure 

the tubing with the clamps provided. 

11.  Open the CO2 regulator ball valve slowly to pressurize the keg.  
12.  Open the TAP faucet slowly to allow the beer to flow through the system. 
13.  Locate the Keg and CO2 bottle inside the refrigerator.  
 
 

NOTE: 

Maintain beer between 34°F and 38°F for proper flow and foam. If beer is over 38°F it will foam out easily. 

 

 

 
 
14.  
 

Picture 3

 

Picture 5

 

REFRIGERATOR’S BACK 

Condenser 

Faucet arm 
Support 
structure 

Evaporator Drain 

NOTE: 

There is no need to remove the refrigerator’s back in order to install the beer 

line. Illustrations are for reference only. 

Picture 4

 

Evaporator 

BEER ACCESS PLUG 

Содержание URS-1













Отзывы: