manualshive.com logo in svg

Alfa level LKH UltraPure-10, Инструкция по эксплуатации

Поделиться
Скачать
Alfa level LKH UltraPure-10 Скачать руководство пользователя страница 25

5 Maintenance

Read the instructions carefully. The items refer to the parts list and service kits section.
Handle scrap correctly.

: Relates to the shaft seal.

Step 5
1. Clean the sealing surfaces with contact cleaner before fitting

back plate (25).

2. Carefully guide the back plate onto adaptor (16).
3. Fit washers (21) and nuts (20).

3001-0034

Step 6
Lubricate O-ring (26) and slide it onto back plate (25).

3001-0035

Step 7
1. Lubricate O-ring (38) and fit it in impeller (37).
2. Lubricate impeller hub with silicone grease or oil.
3. Screw the impeller onto stub shaft (7).
4. Fit impeller screw (39) and tighten.
Torque values:
LKHUP10-60: 20 Nm (15 lbf-ft)
LKHUP70: 50 Nm (37 lbf-ft)

3001-0036

Step 8
Fit safety guards (22) and screw (23) and tighten.
If pump is not supplied with flush connections, the holes in the
adaptor must be covered by the guard.

3001-0037

Step 9
1. Fit pump casing (29), washers (24a) and cap nuts (24).
2. Adjust pump casing to the right position.
3. Tighten nuts (20) for back plate (25) and tighten cap nuts (24).

Torque values:
LKHUP10-20 = 20 Nm/14.8 lbf-ft
LKHUP25-70 = 40 Nm/29.5 lbf-ft

3001-0012

25

Содержание LKH UltraPure-10















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды