Alfa Laval TD 461-702 Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 50

background image

3 Installation

Study the instructions carefully and pay special attention to the warnings!
The valve has welding ends as standard but can also be supplied with fittings.

3.2

General installation

Step 1

!

- CAUTION

Alfa Laval cannot be held responsible for incorrect installation.

- Always release compressed air after use.
- Always read the technical data thoroughly.

See section 6 Technical data.

DO NOT DISASSEMBLE

kg

!

Do NOT attempt to disassemble the actuator due to
spring under load danger!

SPRING UNDER LOAD
Do not attempt to cut open

kg

!

If marked with this warning, do NOT attempt to cut
the actuator open, due to spring under load danger!

Step 2

!

Never touch moving parts if the actuator is supplied with
compressed air.

Moving parts!

Air

Air

2200-0037

Step 3
To avoid water hammering, it is recommended to install the valve
so that the flow is against the spring closing direction.

Shock in the actuator must never occur.

Avoid water
hammering!

Air

Flow

Flow

2200-0120

10

«
...
8
9
10
11
12
...
»

Содержание TD 461-702



















































Отзывы:

Нет отзывов

Похожие инструкции для TD 461-702

Бренд: Samson Страницы: 48

Бренд: Mako Networks Страницы: 15

Бренд: Lawler Страницы: 5

Бренд: VAT Страницы: 29

Бренд: Balboa Instruments Страницы: 19

Бренд: D+H Страницы: 36

Бренд: D-Box Страницы: 4

Бренд: D+H Страницы: 36

Бренд: tams elektronik Страницы: 12

Бренд: Lawler Страницы: 5

Бренд: RadioMaster Страницы: 49

SUPERREMOTE UR19A

Бренд: X10 Страницы: 3

Бренд: Xantech Страницы: 102

Бренд: Xantech Страницы: 17

Бренд: X10 Страницы: 2

Бренд: Zodiac Страницы: 12

Бренд: National Instruments Страницы: 34

Бренд: WAGNER Страницы: 60

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды