manualshive.com logo in svg

Alfa Laval LKH Evap ESE01861-EN4, Инструкция по эксплуатации

Поделиться
Скачать
Alfa Laval LKH Evap ESE01861-EN4 Скачать руководство пользователя страница 7

3 Installation

3.1

Unpacking/delivery

Step 1
Always use a lifting crane when handling the pump (See technical
data).

CAUTION
Alfa Laval cannot be held responsible for incorrect unpacking.

WARNING:
Be aware that certain pump configurations can tilt, and thereby
cause injuries to feet or fingers. The pump should be supported
underneath the adaptor, when not installed in the process line.

Check the delivery for:
1. Complete pump.
2. Delivery note.
3. Motor instructions.

Step 2
Remove any possible packing materials from the inlet and the
outlet.
Avoid damaging the inlet and the outlet.
Avoid damaging the connections for flushing liquid, if supplied.

3000-0060

Remove

packing

materials!

Caution!

Step 3
Inspect the pump for visible transport damages.

Inspection!

3000-0060

Step 4
Always remove the shroud, if fitted, before lifting the pump.

Remove the shroud before lifting!

3000-0061

7

www.sks-online.com 

www.sks-webshop.com

Содержание LKH Evap ESE01861-EN4

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды