background image

NTSA3/9 171130

Two metal placards are included in the Installation

Instruction Envelope packaged with every Sauna Heater.

using the screws or nails provided in the intended location,

at eye level.The CAUTION placard must be attached to the

interior wall of the sauna room directly above the heater

where it is visible to the bather. The WARNING placard

must be attached to the door of the sauna room.

For safety and reliability, the following rules must be

addressed.

All wiring to the sauna heater and accessories shall be

routed away from any direct radiation from the sauna

heater.

No permanent locking or latch system is to be used on

the sauna door.

Acceptable door fittings are: magnetic catches, friction

catches, spring or gravity loaded closures. The door must

always open outwards.

No shower may be installed in a sauna room.

No electrical receptacle shall be installed inside the

sauna room.

The enclosed WARNING: Reduce the risk of

overheating…warning plate must be mounted on or

alongside the door outside the sauna room at about eye

level.

The enclosed CAUTION: Reduce the risk of

fire…caution plate must be mounted on the interior wall

above the heater.

The heater should not be operated without its container

properly filled with rocks and the rock guard in place.

If an intercom speaker is installed, it should be away

from the heater and as close to the floor as possible.

If a room light is installed, it should be a surface

mounted bracket type. Wall mounted lights should be about

70″ above the floor. Ceiling mounted lights should be of an

approved type with a junction box that is remote to the

fixture itself. Use only a fixture that uses A.F.or fixture type

internal wiring. A 60 Watt bulb should provide sufficient

lighting.

Fire sprinkler systems installed inside any sauna room

should be properly rated for sauna room temperatures.

Always mount the heater according to these installation

instructions.

INSTALLATION AND OPERATING INSTRUCTIONS

Page 16

SECTION 13: WARNING PLACARDS

WARNING

The “CAUTION” and

“WARNING” placards must

be mounted in accordance

with Section 13.

For safety purpose sauna

door must open out and not

lock.

Never use a wood stain, seal

or preservative on the inside

of your sauna room.

Light fixtures get very hot

during operation. Locate

light fixture where it will not

be a burn hazard.

SECTION 14: ROOM CONSTRUCTION

Содержание NTSA Series




















Отзывы: