ALDI 700069 страница 34 Скачать руководство пользователя

Страница: 34 / 40

Digital Inverter Generator with Pure Sine Wave

AFTER SALES SUPPORT

e-mail: [email protected]

1300 889 028

MODEL: №. XG-KF2000 • 03/2020 • 700069

(toll free)

AFTER SALES SUPPORT

(toll free)

e-mail: [email protected]

1300 889 028

Digital Inverter Generator with Pure Sine Wave

MODEL: №. XG-KF2000 • 03/2020 • 700069

Troubleshooting

Trouble

Possible cause

Suggested remedy

Engine will not start

1. Low on fuel or oil content

1a Fully fill tank. Ensure fuel is fresh
1b Ensure oil is at the the correct level.

Refer page 18-19 of this manual.

1c Ensure the generator is horizontal and

not on an angle.

1d Turn the fuel tap lever to the right

in a clockwise direction to turn OFF

the fuel tap / lever(23). Loosen the

carburettor drain screw. Allow the fuel

in the carburettor bowl to totally drain.

When the fuel has stopped draining,

turn the fuel tap / lever to the left in an

anti-clockwise direction to turn ON and

fuel starts running out of the carburettor

drain. If so, tighten the screw on the

drain and allow the carburettor to fill

with petrol.

1e If the fuel from the tank does not pass

through the carburettor drain above,

you need to drain the fuel tank (27),

remove the fuel tap / lever (23) and

inspect the fuel extension filter (22).

2. Engine On/Off switch (2) in “Off”
position

2. Press the engine On/Off switch (2) to

the “ON” position as indicated by an “I”.

3. Faulty spark plug (20)

3. Replace or clean spark plug (20) Refer

page 27.

4. Choke lever (16) in wrong position

4. Adjust choke lever (16) accordingly

Refer to page 22.

5. Fuel shut-off valve in closed position

5. Open fuel shut-off valve

6. Unit loaded during start-up

6. Remove load from unit

7. Spark plug (20) wire loose

7. Attach wire to spark plug (20)

8. Old fuel in carburettor

8. Fuel will deteriorate in the carburettor

fuel bowl very quickly. Open the drain

screw in the bowl of the carburettor until

fresh fuel runs through.

9. If all of the above checked ok

9. Take unit to service centre

Содержание 700069









































Результаты поиска

Содержание 700069

Отзывы:

Похожие инструкции для 700069

Бренды по названию

Популярные бренды

ALDI 700069, Руководство пользователя

Результаты поиска

Содержание 700069

Отзывы:

Похожие инструкции для 700069

Бренды по названию

Популярные бренды