Alcolizer WM4 Скачать руководство пользователя страница 35

Страница: 35 / 41

REF: WM4 User Manual V7.docx

Page 35

•

13.2

Configuration

There are three relays available and their behaviour can be configured on the

Relays

page.

For each relay the following properties can be configured:

•

Enabled:

If checked, indicates that the relay should respond to breath test results

and enables remaining configuration items for the relay.

•

Min:

If a result is greater than this value the relay should turn on for the configured

duration. If the minimum value is 0.00 for example, the relay should turn on if the
value of the result is greater than or equal 0.00.

•

Max:

If a result is less than this value the relay should turn on for the configured

duration. If the maximum value is 0.00 the relay should turn on if the value of the
result is less than or equal 0.00.

•

Duration:

If the relay is enabled and a breath test result falls within its configured

range, the relay should fire for a number of seconds equal to the configured
duration.

The

Relay Status

indicates if the relay is currently

OFF

There are three buttons on this page that briefly activates the relays.

NOTE

It is possible for breath test results near a configured value for the relays to act differently

depending on whether the actual value was slightly above or below the displayed value.

This is due to the nature of the analog input from the fuel cell and possible rounding

behaviour below the precision of the displayed value.

In this situation the instrument will

not

activate two relays in the situation where one

relay shares a nonzero maximum with the minimum value from another relay.

Содержание WM4










































Результаты поиска

Содержание WM4

Отзывы:

Бренды по названию

Популярные бренды

Alcolizer WM4, Руководство пользователя

Результаты поиска

Содержание WM4

Отзывы:

Бренды по названию

Популярные бренды