manualshive.com logo in svg

Alcatel OmniStack 6124, Руководство пользователя

Поделиться
Скачать
Alcatel OmniStack 6124 Скачать руководство пользователя страница 67

Monitoring the Switch

2-55

Configuring Static Unicast Addresses

Use the Static Unicast Address Table Configuration screen to manually configure 
host MAC addresses in the unicast table. You can use this screen to associate a 
MAC address with a specific VLAN ID and switch port as shown below.  

Alcatel OmniStack 6148

< Static Unicast Address Table Configuration >

VID

MAC Address

Unit

Port

Status

------------------------------------------------------------

1

00-00-00-E8-43-12

1

1

Permanent

Sorted by : VID + MAC

VID

: 1

MAC : 00-00-00-00-00-00

VID : 1

Port : 1

MAC : 00-00-00-00-00-00

Status : Permanent

[Show]

[More]

[Set]

<OK>

Use <TAB> or arrow keys to move, <Enter> to select.

Menu

Description

VID

The VLAN group this port is assigned to.

MAC Address

The MAC address of a host device attached to this switch.

Unit

The switch unit the host device is attached to.

Port

The port the host device is attached to.

Status

The status for an entry can be set to:
Permanent 

This entry is currently in use and will remain so after 

the next reset of the switch.

DeleteOnReset 

This entry is currently in use and will remain so until 

the next reset.

Invalid 

Removes the corresponding entry.

DeleteOnTimeOut

This entry is currently in use and will remain so until 

it is aged out. (Refer to “Aging Time” on page 2-53.)

Other 

This entry is currently in use but the conditions 

under which it will remain so differ from the 

preceding values.

Sorted by

Selects the primary sort key for displaying table entries. Note that only 

VID+MAC is implemented in the current firmware release.

[Show]

Displays the static address table sorted on VID as the primary key and MAC 

address as secondary key.

[More]

Scrolls through entries in the static address table.

[Set]

Adds the specified entry to the static address table, such as shown in the 

following example: 

VID

: 1

MAC : 00-00-00-e8-34-22

Unit

: 1

Port: 1

Status

: Permanent

Содержание OmniStack 6124









































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды