Alcatel-Lucent OmniSwitch 6850E Series Скачать руководство пользователя страница 55

Страница: 55 / 182

OmniSwitch 6850E Series Chassis and Hardware Components

Mounting the Switch

OmniSwitch 6850E Series Hardware Users Guide

January 2013

page 2-37

After the rack-mount flanges are secured to the chassis, mark the holes on the rack where the switch is

to be installed.

Lift and position the switch until the rack-mount flanges are flush with the rack post.

Align the holes in the flanges with the rack holes that were marked in step 3.

Once the holes are aligned, insert a rack mount screw (not provided) through the

bottom hole of each

flange

. Tighten both screws until they are secure.

Attaching the Switch to the Rack

Note

Be sure to install the screws in the

bottom hole

of each flange, as shown, before proceeding.

Once the screws at the bottom of each flange are secure, install the remaining two rack mount screws.

Be sure that all screws are securely tightened.

Note.

If you are installing multiple switches in a rack to form a stacked configuration, refer to

“Setting Up

a Stacked Configuration” on page 2-38

Installing and Removing Combo Port SFPs

OmniSwitches offer four Gigabit Ethernet combo ports, located on the front panel (see

page 2-2

). These

combo ports support hot-swappable fiber Small Form-Factor Pluggables (SFPs). For instructions on
installing and removing combo connector SFPs, refer to the

OmniSwitch Transceivers Guide

Содержание OmniSwitch 6850E Series























































































































































































Результаты поиска

Содержание OmniSwitch 6850E Series

Отзывы:

Похожие инструкции для OmniSwitch 6850E Series

Бренды по названию

Популярные бренды

Alcatel-Lucent OmniSwitch 6850E Series, Руководство пользователя по оборудованию

Результаты поиска

Содержание OmniSwitch 6850E Series

Отзывы:

Похожие инструкции для OmniSwitch 6850E Series

Бренды по названию

Популярные бренды