Alcatel-Lucent OmniSwitch 6850E Series Скачать руководство пользователя страница 106

Страница: 106 / 182

OmniSwitch BPS Power Connections

OmniSwitch Backup Power Shelf/System (BPS)

page 4-18

OmniSwitch Backup Power Shelf/System (BPS)

January 2013

Installing and Connecting System Power

Orient the power supply so that the power cord socket is situated at the right of the power supply. Also,

for the power supply to seat properly, make sure that the handle is in the vertical position.

Slide the power supply back until it is securely seated in the chassis backplane.When the connector is

fully seated, the lock tab will click and hold the power supply in place.

Plug the power cord (provided) into the power supply’s socket.

Note.

The chassis

does not

provide an on/off switch. Connecting a minimum of one system power supply

and one PoE power supply to a power source will power on the OS-BPS chassis and any attached
switches.

Содержание OmniSwitch 6850E Series























































































































































































Результаты поиска

Содержание OmniSwitch 6850E Series

Отзывы:

Похожие инструкции для OmniSwitch 6850E Series

Бренды по названию

Популярные бренды

Alcatel-Lucent OmniSwitch 6850E Series, Руководство пользователя по оборудованию

Результаты поиска

Содержание OmniSwitch 6850E Series

Отзывы:

Похожие инструкции для OmniSwitch 6850E Series

Бренды по названию

Популярные бренды