background image

PX915-DV 

 
Copyright 

All rights are reserved. No part of this publication may be reproduced, transmitted, transcribed, 
stored in a retrieval system or translated into any language or computer language, in any form or by 
any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the 
prior written permission of the company. Brands and product names are trademarks or registered 

trademarks of their respective companies. 
The vendor makes no representations or warranties with respect to the contents herein and especially 
disclaim any implied warranties of merchantability or fitness for any purpose. Further the vendor 
reserves the right to revise this publication and to make changes to the contents herein without 
obligation to notify any party beforehand. Duplication of this publication, in part or in whole, is not 
allowed without first obtaining the vendor’s approval in writing. 

 

Trademark 

All the trademarks or brands in this document are registered by their respective owner. 

 

Disclaimer 

We make no warranty of any kind with regard to the content of this user’s manual. The content is 
subject to change without notice and we will not be responsible for any mistakes found in this user’s 

manual. All the brand and product names are trademarks of their respective companies. 

 

FCC Compliance Statement 

This equipment has been tested and found to comply with the limits of a Class B digital device, 
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection 
against harmful interference in a residential installation. This equipment generates, uses and can 

radiate radio frequency energy and, if not installed and used in accordance with the instructions, may 
cause harmful interference to radio communications. Operation of this equipment in a residential area 
is likely to cause harmful interference in which case the user will be required to correct the 
interference at his own expense. However, there is no guarantee that interference will not occur in a 
particular installation. 

 

CE Mark 

The device is in accordance with 89/336 ECC-ENC Directive. 

 
 
 
 
 

PX915-DV

 

Intel

®

 

915PL & ICH6 

Support Socket 775 Intel

®

 Pentium

®

 4   

Ver: EG100 

 

Содержание PX915-DV


















































Отзывы: