background image

 

 

K8Ultra-U Series

 

 

 

Copyright 

All rights are reserved. No part of this publication may be reproduced, transmitted, 
transcribed, stored in a retrieval system or translated into any language or computer 
language, in any form or by any means, electronic, mechanical, magnetic, optical, 
chemical, manual or otherwise, without the prior written permission of the company. 
Brands and product names are trademarks or registered trademarks of their respective 
companies. 
The vendor makes no representations or warranties with respect to the contents herein 
and especially disclaim any implied warranties of merchantability or fitness for any 
purpose. Further the vendor reserves the right to revise this publication and to make 
changes to the contents herein without obligation to notify any party beforehand. 
Duplication of this publication, in part or in whole, is not allowed without first obtaining 
the vendor’s approval in writing. 

 

Trademark 

All the trademarks or brands in this document are registered by their respective owner. 

 

Disclaimer 

We make no warranty of any kind with regard to the content of this user’s manual. The 
content is subject to change without notice and we will not be responsible for any 
mistakes found in this user’s manual. All the brand and product names are trademarks of 
their respective companies. 

 

FCC Compliance Statement 

This equipment has been tested and found to comply with the limits of a Class B digital 
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide 
reasonable protection against harmful interference in a residential installation. This 
equipment generates, uses and can radiate radio frequency energy and, if not installed 
and used in accordance with the instructions, may cause harmful interference to radio 
communications.  Operation of this equipment in a residential area is likely to cause 
harmful interference in which case the user will be required to correct the interference 
at his own expense. However, there is no guarantee that interference will not occur in a 
particular installation. 

 

CE Mark 

The device is in accordance with 89/336 ECC-ENC Directive. 

 

 
 

120410134M1N 

Содержание K8Ultra-U Series
















































Отзывы: