Albalá Ingenieros ASW3000C01 Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 34

background image

Albalá Ingenieros | Manual

ASW3000C01

The lines indicated as GPIO n the silkscreening are assigned as follows:

GPIO5: Error input for the reserve channel.

GPIO4: Error input for the main channel.

GPIO3: Alarm output for the reserve channel.

GPIO2: Alarm output for the main channel.

GPIO1: Indicates selection of:

0V main channel.

+5V reserve channel.

GND: Ground for the module.

During normal operating conditions the alarm outputs GPIO2 and GPIO3 are set to
logic low (transistor on) in order to signal an alarm condition and a no-alarm
condition via a logic high (open collector). This signaling polarity can be inverted using
the control software.

16

«
...
14
15
16
17
18
...
»

Содержание ASW3000C01



































Отзывы:

Нет отзывов

Похожие инструкции для ASW3000C01

Бренд: Lantronix Страницы: 40

Бренд: Lantronix Страницы: 2

SISTP1040-551-LRT

Бренд: Lantronix Страницы: 2

Бренд: Lantronix Страницы: 2

SISPM1040-3 L Series

Бренд: Lantronix Страницы: 2

SISPM1040 L3 Series

Бренд: Lantronix Страницы: 36

SecureLinx Spider

Бренд: Lantronix Страницы: 18

Бренд: Lantronix Страницы: 8

Бренд: Lantronix Страницы: 6

SISPM1040-582-LRT

Бренд: Lantronix Страницы: 272

Xpress-Pro SW 52000

Бренд: Lantronix Страницы: 8

Бренд: DITEC Страницы: 8

Бренд: protech Страницы: 4

AW-FGT-100C-120

Бренд: Vivotek Страницы: 2

Бренд: AbleNet Страницы: 12

BONANZA ACCU-SIM V35B

Бренд: A2A Simulations Страницы: 112

FRIENDLYNET FS4116R

Бренд: Asante Страницы: 6

IPS-800CE-D16, IPS-1600CE-D16

Бренд: Western Telematic Страницы: 58

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды