background image

Rev.010918-BR 

 

www.akiascreens.com

 

 

 

Motorized Series 

Electric Wall/Ceiling Projection 
Screen

 

USER’S GUIDE 

 

 

Important Safety & Warning Precautions 

Make sure to read this user’s guide and follow the procedures below. 

 

Caution

: The screen’s Black Top Drop is already set to its maximum drop distance. There is NO extra 

Black Top Drop in the roller. Please be aware of this as it will void your warranty with AKIA  Screens. 
Unapproved changes or modifications (except for cutting the power cord for hardwire installations) to this 
unit are prohibited and will void your warranty. For more information, please contact our Technical Support 
Department at (877) 511-1211. 
 

 

Please retain this user’s guide for future reference. 

 

To avoid damaging the unit, do not use with any unauthorized accessories not recommended by the 
manufacturer.  

 

Handle the unit carefully during transportation to avoid any damages. 

 

To ensure safe and reliable operation, direct connection to a properly grounded power source is 
advised. 

 

The power outlet supplying power to the unit should be close to the unit and easily accessible. 

 

Do not install the unit on uneven or inclined surfaces. 

 

Do not put heavy objects on the power cord and position it properly to avoid creating a trip 
obstacle. 

 

Never overload the power cord to prevent an electric shock or fire due to a loose contact or a short 
circuit. 

 

There are not user serviceable parts in this unit. Do not attempt to disassemble this unit by yourself. 
No one except authorized technicians can open and make repairs to this unit. 

 

Make sure the power source this unit is connected to has a continuous power flow. 

 

If there is need to use an extension cord, make sure the cord has an equal rating as the appliance to 
avoid overheat. 

 

Do not handle the power plug when your hands are wet or your feet are in contact with water. 
 

Do not use this unit under the following circumstances. 

 

Disconnect the power cord under the conditions of heavy rain, wind, thunder or lightning.

 

 

Avoid direct Sunshine, rain shower and moisture.

 

 

Keep away from fire sources and high temperature to prevent this device from overheating.

 

 

Cut off the power supply first before transportation or maintenance.

 

 

Fully disconnect from the power supply when the unit is not in use for a long period of time, as 
should be done with any other electric household appliance.

 

 

To avoid possible injury and/or an electric shock, do not attempt to use the screen if there is 
obvious damage or if there are any evident broken parts.

 

 
NOTE: 

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to 
Part 15 of the FCC Rules. 
 

Содержание Motorized Series









Отзывы: