background image

10042022JA 

                                              

www.akiascreens.com

                        

U

-00232 

EDGE FREE® CLR® 2 Series

 

Ceiling Light Rejecting Fixed Frame Screen

 

USER’S GUIDE – V1.1 

   

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Product Description: 

 

The 

EDGE FREE® CLR® 2 Series

 is a fixed frame projection screen that uses Akia’s 

EDGE FREE®

 technology. 

The EDGE FREE® design resembles a giant size flat panel TV display. The screen includes a bezel trim to further 
enhance the frame appearance and absorb projector overshoot. An optional LED kit is available for backlighting.  
The screen material included is our 

ISF Certified

 

CLR® 2

 (Ceiling Light Rejecting) which is a front projection 

material designed for ultra and short throw projectors, precisely formulated for environments with minimal control of 
overhead room lighting. Its multi-layer structure 

enhances picture brightness

maintain color purity,

 and 

improves 

contrast levels

 in ambient light room environments. The 

CLR® 2

 is best for family rooms, educational facilities, 

conference rooms, house of worship or any applications in which incident light is a factor. 

 

Screen Maintenance 

Dust, dirt and scratches on the projection screen surface will affect the quality and performance of the projection 

image. For optimal results we advise to pay attention to the following instructions.

 

1)

 

Use a dry microfiber cloth or soft brush to remove dust from the screen’s surface. 

 

2)

 

When cleaning, use a damp microfiber cloth with warm water to remove any marks. 

 

3)

 

Never rub or apply pressure when cleaning the surface

 

4)

 

The screen material has a scratch-resistant layer to protect the material through many years of use. 

Notes

The following precautions should always be followed to avoid damaging the material, which is not covered 

under warranty. 

 

Don’t 

touch

 the screen material with your bare hands to avoid leaving oil residue from fingertips.  

Use gloves when handling the material

 

Don’t 

point 

to the screen material with a fingertip or other sharp objects to prevent damage to the material. 

 

Don’t 

use

  acetone,  benzene,  alcohol  and  any  other  organic  solvents  to  clean  the  screen  material.  

Using such chemicals will permanently damage the screen. 

 

1. Frame and Edge Trim Parts List

 

Qty 

 

item 

2 pcs 

Main Frame Parts 

Qty 

 

item 

2 pcs 

Edge Trim Parts 

Part A. 

vertical frame 

        

 

Part D. 

 

Part B. 

½ horizontal frame 

 

Part E. 

 

Part C. 

½ horizontal frame

  

Part F. 

 

Содержание EDGE FREE CLR 2 Series









Отзывы: