Akia Screens EDGE FREE CLR 2 Series страница 7 Скачать руководство пользователя

Страница: 7 / 8

10042022JA

www.akiascreens.com

-00232

Step 11

: Install the

angle cover

(

) on each corner of the frame using the

M4x4 screws (m)

Note: The angle cover screws holes align with the screw holes on the elbow joint.

Step 12

: Install the

springs (q)

in each middle area to further support the bezel trim edge frame.

Notice to Installer:

Material Tip

Proper Projector Placement for CLR®2

CORRECT

The

CLR®2

is exclusively for tabletop

mounted

ultra

and

short throw

projectors.

INCORRECT

Overhead placement or a standard projector

will make the image very dark, on account of

the screen’s absorbent layer deflecting light

that is not aligned with its reflective angle.

Peel off the double-sided tape.

Содержание EDGE FREE CLR 2 Series









Результаты поиска

Содержание EDGE FREE CLR 2 Series

Отзывы:

Похожие инструкции для EDGE FREE CLR 2 Series

Бренды по названию

Популярные бренды

Akia Screens EDGE FREE CLR 2 Series, Руководство пользователя

Результаты поиска

Содержание EDGE FREE CLR 2 Series

Отзывы:

Похожие инструкции для EDGE FREE CLR 2 Series

Бренды по названию

Популярные бренды