background image

The system can also automatically deactivate devices
when the set number of alarms is exceeded or when the
recovery timer expires

User Guide

Opens the User Guide for detector

Unpair Device

Disconnects the detector from the hub and deletes its
settings

Indication

Event

Indication

Note

Turning on the detector

Lights up green for about one second

Detector connection to the 

,

 and 

Lights up continuously for a few
seconds

Alarm / tamper activation

Lights up green for about one second

Alarm is sent once in 5 seconds

Battery needs replacing

During the alarm, it slowly lights up
green and slowly goes out

Replacement of the detector battery
is described in the 

 manual

Functionality testing

The Ajax security system allows conducting tests for checking the functionality of connected
devices.

The tests do not start immediately but within a period of 36 seconds when using standard
settings. The test time start depends on the settings of the detector ping interval (the paragraph
on “Jeweller” settings in hub settings).

Detector functionality testing

Having de ned the location of the detector and having  xed the device with the bundled
adhesive tape, test the detection zone.

GlassProtect does not react to clapping!

Testing the detector

Hit the glass with your  st without breaking it. If the detector catches a low-frequency sound, the
LED blinks. Simulate a high-frequency glass shattering sound for 1.5 seconds after the  rst hit
with a special tool or hitting a glass with a metal object. After recognizing the sound, the
detector switches off the LED indicator for a second.

To be triggered when the system is armed, the detector needs to recognize sounds in the following order:
low-frequency sound (hit)  rstly, then high-frequency sound (glass shattering, shards). Otherwise, the alarm
will not go off.

Switch on/off all the appliances that usually operate in the room: generators, air conditioners,
etc. If this triggers the detector, try to change the sensitivity or relocate GlassProtect.

Use the sensitivity level, at which the detector correctly passes both test stages and does not
respond to any devices operating in the room.

Installing the device

Selecting the Location

In some cases, the household activity can cause false alarms

The location of GlassProtect depends on its remoteness from the hub, and obstacles hindering
the radio signal transmission: walls,  oors, large objects inside the room.

The device developed only for indoor use.

Check the Jeweller signal level at the installation location

Learn more about auto deactivation of
devices

hub

ocBridge Plus

uartBridge

Battery

Replacement

Jeweller Signal Strength Test

Detection Zone Test

Attenuation Test

Содержание GlassProtect








Отзывы: