AJ 31088, Руководство по эксплуатации

Страница: 171 / 183

2 | 01-2811700 • ajproducts.ie
Note: Do not attempt to repair the truck unless you are trained and authorized.
4. MAINTENCE
4.1 Hydraulic oil
Please check the oil level every six months. The oil can be hydraulic oil: ISO VG
32(GB11118-89), its viscosity should be 32cSt at 40, total volume is about 4.Olt.
4.2 Daily check and maintenance
It is necessary to check the truck daily. Special attention should be paid to the
rollers, the axles, as thread, rags, etc., it may block the rollers; the scissors
and the table should be checked, they may be deformed; the table should be
unloaded and lowered in the lowest position when the job is over.
4.3 Lubrication
Use motor oil or grease to lubricate all movable parts.
5. TroubLEsHooTINg
Trouble Clause Fixing methods
The table can
not be up the
max. height
- The hydraulic oil is not enough
- The position of the travel
switch
- Pour in the oil
- Adjust the position of
travel switch
The table can
not lift.
- Without hydraulic oil.
- Safety valve has no enough
pressure.
- Pour in the oil
- Adjust the safety
valve
The motor can -
not run
- The emergency switch is
turned off
- The connection of electrical
wire is loose.
- The contactor of DC motor is
damaged.
- Turn the emergency
switch clockwise;
- Tight it;
- Replace it with a
new one
The table cannot
descend
- The piston rod or cylinder is
deformed resulting from partial
loading slanting to one side or
over-loading.
- The fork was kept in the high
position for long time, which
cause piston rod bared to
arise in rusting and jamming
of the rod.
- The release valve of pump can
not work because of abrasion
- Replace the piston
rod or cylinder with
new one
- Keeping the fork in
the lowest position if
not using, and pay
more attention to
lubricate the piston
rod.
- Replace with new
one
Leaks - Sealing parts worn or dama -
ged.
- Some parts cracked
- Replace with
new one
- Replace with
new one
The fork de -
scends without
the release valve
worked
- The impurities in the oil cause
the release valve to be unable
to close tight.
- Sealing parts worn or
damaged.
- The release valve is damaged.
- Replace with new oil
- Replace with new
one
- Replace with new
one
Welcome to use our electrical lift table. This lift table is made
of high quality steel and is designed to give a durable, reliable
and easy to use. For your safety and correct operation, please
carefully read this instruction and warnings on the lift table
before using it.
1. sPECIFICATIoNs
Type HIW1.0Eu HIW2.0Eu
Capacity 500 kg 1000 kg
Max. height 1010 mm 1010 mm
Min.height 190 mm 190 mm
Dimension of the table 1300 x 800 mm 1300 x 800 mm
Lifting speed 15 s 26 s
Lower speed 13 s 20 s
Pump electric current 3 l/min 3 l/min
Oil tank 2 l 2 l
Pump station AC3 x 380V, 750W AC3 x 380V, 750W
Weight 160 kg 220 kg
Type HIW4.0Eu HIW3.0Eu
Capacity 2000 kg 3000 kg
Max. height 1010 mm 1020 mm
Min.height 190 mm 220 mm
Dimension of the table 1300 x 800 mm 1300 x 800 mm
Lifting speed 40 s 26 s
Lower speed 30 s 22 s
Pump electric current 3 l/min 5 l/min
Oil tank 3 l 3 l
Pump station AC3 x 380V, 750W AC3 x 380V, 1500W
Weight 280 kg 320 kg
2. sAFETY guIDANCE
2.1
Operator should read all warning signs on the truck and instructions here
before using it.
2.2 Do not put foot and hand under the scissors, injury could happen.
2.3 Do not enter under table.
2.4 Do not overload.
2.5
Do not use it on slope, lift table may become uncontrollable and create
danger.
2.6 Do not lift persons. People could fall down and suffer severe injury.
2.7 Do not side or end load .Load must be distributed on at least 80% of the
table area
2.8
The table should be maintained by the professional operator.
2.9 Keep watching the condition of load, stop operating lift table if load
becomes unstable.
2.10 Check and maintain the lift table regularly.
2.11 Do not use the lift table continuously, the pump station would be
damaged.
2.12 Stop operating the lift table if the temperature of the oil is too high.
2.13 The table should be lowered to the bottom if the lift table is not used.
3. oPErATINg guIDANCE
3.1 Emergency switch
When you press down this switch, it will switch off the power, and then you turn it
clockwise, it will switch on the power.
3.2 Lifting switch
When you press down this switch, the table will lift; when you loose your hand,
the table will stop lifting.
3.3 Lowering switch
When you press down this switch, the table will be lowering; when you loose
your hand, the table will stop lowering.
3.4 The table can not lift or lower when the function of safety protection frame
starts. When you press down the lifting or lowering switch, the table will lift
or lower again.
Attention:
Environmentally hazardous waste, such as batteries and electronics,
will have a negative effect on the environment, or health, if handled
incorrectly.
The waste packages should be sorted and put into solid dustbins
according to the materials and be collected disposal by local special
environment protection bureau. To avoid pollution, it’s forbidden to
throw away the wastes randomly.
To avoid leaking during the use of the products, the user should
prepare some absorbable materials (scraps of wooden or dry duster
cloth) to absorb the leaking oil in time. To avoid second pollution to
the environment, the used absorbable materials should be handed in
to special departments in terms of local authorities.
Note:
All of the information reported herein is based on data available at the
moment of printing. We reserve the right to modify our own products
at any moment without notice and incurring in any sanction. So, it is
suggested to always verify possible updates.