AJ Aircraft Acuity Скачать руководство пользователя | Manualshive

Страница: 9 / 24

background image

aj-aircraft.com

Page 8

With the servo installed mark the mounting hole
locations. Pre-drill for servo mounting screws using a
1/16” drill. Install the servo with the wood screws that
came with your servos. Remove the screws and servo.
Apply a drop of thin CA glue into each mounting screw
hole. This will harden the wood around the screws and
provide a more secure installation. (Allow the CA glue to
dry before reinstalling the servo.)

Reinstall the servo.

Assemble a ball link to each end of a connecting rod.
Connect a ball link to a servo horn and the aileron control
horn. Use a socket head screw, a flat washer and a nylon
lock nut. (The brass ball in the link is offset. The larger
reveal side should be against the control horn as shown
below.)

Check the length of the assembly to the servo with the
aileron level with the wing. Once the correct length of
the assembly is found connect the servo arm to the servo.
(Always adjust the connecting rod length with the servo
powered up and centered.)

«
...
7
8
9
10
11
...
»

Содержание Acuity

























Отзывы:

Нет отзывов

Похожие инструкции для Acuity

Бренд: Jamara Страницы: 16

Бренд: 4-Max Models Страницы: 8

Бренд: 4-Max Страницы: 38

Бренд: BARCLONE Страницы: 14

Бренд: Blade Страницы: 17

Бренд: Pinolino Страницы: 12

Бренд: E sky Страницы: 32

MINI-Z Racer MR-03N HM MINI COOPER S

Бренд: Kyosho Страницы: 2

Fun 2 Learn J6870

Бренд: Fisher-Price Страницы: 8

Бренд: Opale-Paramodels Страницы: 6

Бренд: Smoby Страницы: 4

WOODEN PROJECT WORKBENCH

Бренд: Melissa & Doug Страницы: 16

GIZMOS & GADGETS

Бренд: Littlebits Страницы: 13

Бренд: beeloom Страницы: 11

Lightning McQueen Learning Laptop

Бренд: VTech Страницы: 10

Project Mc2 Ultimate Makeover Bag

Бренд: MGA Entertainment Страницы: 2

Grab & Go Koala 5368

Бренд: VTech Baby Страницы: 10

HALF-TIMBERED HOUSE 131246

Бренд: Faller Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды