T
RADIO RECEPTION
Tuning in to a station
→
O
1 Press BAND TUNER ON repeatedly to select AM or FM.
2 Press TUNING
+
(
t
) or
-
(
r
) to tune in to a station.
After listening, press
s
STOP/OFF/CHARGE to turn off the radio.
For better reception
→
P
FM: The headphone cord functions as the FM antenna. Keep it extended.
AM: Turn the unit to find the position which gives the best reception.
To listen to an FM stereo broadcasting
When a tuned in station is in stereo, ST changes to
.
When the FM stereo signal is weak and distorted, press MONO/ST. ST goes out
and the sound will be heard in monaural but distortion will be reduced.
Note
• Do not open the disc compartment during radio reception. The buttons will be
deactivated.
• The power is turned off automatically if no operation is made after 5 or 6 hours
from the last operation during radio reception.
Changing AM steps
→
Q
Radio broadcasts have different frequency ranges and changes in different
steps in different countries.
This unit is factory-set to 10 kHz steps on AM. When using the unit where
the AM step changes to 9 kHz, change it as follows.
1 In stop mode, keep BAND TUNER ON pressed for 8 seconds. “S-10” is
displayed for 5 seconds.
2 While “S-10” is displayed, press PRESET CALL UP/DOWN to display
“S-9”.
3 Press ENTER/DISP within 5 seconds.
To resume to 10 kHz, change in the similar way.
Note
When the AM step is changed, stations that you preset are erased.
PRESETTING STATIONS
→
R
You can preset up to total of 30 stations on AM and FM.
1 Press BAND TUNER ON repeatedly to select AM or FM.
2 Press TUNING
+
(
t
) or
-
(
r
) to tune in to a station.
3 Press ENTER/DISP to preset the station.
a
Preset number
To preset more stations, repeat steps 2 and 3.
Listening to preset stations
→
S
1 Press BAND TUNER ON repeatedly to select AM or FM.
2 Press PRESET CALL UP/DOWN repeatedly to select the preset number.
After listening, press
s
STOP/OFF/CHARGE to turn off the radio.
Changing the presetting
1 Press PRESET CALL UP/DOWN repeatedly to select the preset number
you wish to change.
2 Keep ENTER/DISP pressed for 1 or more seconds until the preset number
and the frequency flash.
3 While the preset number is flashing, press TUNING
+
(
t
) or
-
(
r
)
to tune in to a station.
4 Press ENTER/DISP to preset the station on the selected preset number.
If the flashing stops, repeat the procedure from step 2.
Erasing the presettings one by one
Press
s
STOP/OFF/CHARGE after step 2 in “Changing the presetting” above.
Each preset station is erased. All the settings move up by ones and the preset
numbers are refreshed.
Erasing all of the presetting
Keep ENTER/DISP pressed, then press BAND TUNER ON when the frequency
and preset number starts flashing.
CONNECTING TO AN EXTERNAL UNIT
→
T
Use a commercially available connection cord which has a 3.5 ø stereo mini-
plug at one end and two phono plugs at the other end.
Connect the stereo mini-plug to the PHONES/LINE OUT jack of the unit and
connect the phono plugs to the analog input terminals of the external unit, such
as the amplifier or the equipment with the built-in amplifier. The CD sound can be
heard through the connected audio system.
Note
• Turn off the power of both units before connection.
• DO NOT connect to the PHONO inputs of an amplifier (with a built-in
phonoequalizer-amplifier).
• Adjust the volume and DSL on this unit.
O
1
2
P
Q
S
BAND
TUNER ON
FM
AM
R
1
2
3
BAND
TUNER ON
ENTER/DISP
