manualshive.com logo in svg

Aiwa TV-AN1410, Руководство по обслуживанию

Поделиться
Скачать
Aiwa TV-AN1410 Скачать руководство пользователя страница 8

– 8 –

Because the video signal output from a pattern generator is used as the
adjustment signal input during adjustment, the video signal output from
the pattern generator must conform with the specifications. Measure the
output waveform across 75

Ω

 load. Confirm that the synchronizing signal

has an amplitude of about 0.3V, the video signal portion has an amplitude
of about 0.7V and the burst signal has an amplitude of about 0.3V with
flat envelope. Confirm that ratio of the burst signal amplitude and the
red signal amplitude is 0.30 : 0.66. If the output signal does not conform
with the specifications, calibrate the pattern generator. (Refer to pattern
generator operation manual.)
Use the LEADER: LCG 404 for the pattern generator.

Fig. 1-1

 TV display

1.  CRT Adjustment

1-1. Precautions

(1) Receive the white raster signal, and then perform aging for at least

20 minutes.

(2) Demagnetize the area surrounding the CRT with a degausser before

making adjustments.

(3) Set the picture quality for each mode to the factory setting.
(4) Position the front screen facing to the east as much as possible.

1-2. Purpose

(1) Beam landing adjustment (purity magnet)

Set the left/right balance of beam landing. If there is a discrepancy
in this adjustment, a color irregularity will occur. After completion
of the landing adjustment, it is necessary to perform a convergence
adjustment.

Color
irregularity

Color
irregularity

  Before adjustment              After adjustment

ADJUSTMENT

Color bar signal of a pattern generator

Precautions Before Starting Adjustment

Satisfy the following setting conditions before starting adjustment.
• Allow warm-up of 20 minutes or longer.

(Do not turn off during warm-up.)

• Set all picture quality controls of users' setting to initial set-up, unless

otherwise specified.

• Picture quality reset

1. Select "Picture" on the screen menu and press enter button.
2. Select "Normal" and press enter button.
3. Select "Reset" and press enter button.

• Set the pattern generator’s output level to 1.0Vp-p (across 75

Ω

 load).

Approx.
0.3V

Approx. 0.3V

Burst signal

1 Vp-p

White (Approx.

75%)

Approx. 0.7V

Y

ellow

Cyan

Green

Magenta

Red

Blue

Black

75% white

Set-Up For Adjustment

Содержание TV-AN1410





















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды