Aitchison Reese Agri UFO SEEDKING Professional Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 42

Aitchison Reese Agri UFO SEEDKING Professional Скачать руководство пользователя страница 22

20

CALIBRATION

The Aitchison SK2122 has Calibration Trays attached; these
trays are to be used to catch the products that have been
metered from the seed and fertiliser boxes.

SEED BOX CALIBRATION

The seed box has two yellow Calibration Trays (inspection panels)
attached to its front, covering the seeder units. These trays can be
removed and placed under the seeder units to catch the seed.
You can use one of both of these trays.

Calibration Tray

Cup Tray Clip

Cup Tray

Cup Tray

Cup Tray Clip

Calibration Tray

CALIBRATION TRAY PLACEMENT

1. Remove one or both Calibration Trays.
2. Pull out Cup Tray Clips (Cup Tray should swing down).
3. Insert Calibration Tray on top of Cup Tray.
4. Use Cup Tray Clip to hold Calibration Tray in place.
5. Push “ENTER” on EAGLE Seeder Console (refer to EAGLE Operators

Manual).

6. Remove Calibration Tray (with metered seed).
7. Pour seed from Calibration Tray (weigh seed).
8. NOTE: Always prime system before calibration.

NOTE:

If using only

one

Calibration Tray you will have to multiply the weight

of seed by

2

to get correct answer before entering it into the EAGLE

Console.

NOTE:

When new (from factory) the Seed Pads are covered in white powder,
this powder is to prevent the pads being stuck together during
manufacturing.
Until this powder has worn away (or been removed) inconsistent
calibration will result.

«
...
20
21
22
23
24
...
»

Содержание Reese Agri UFO SEEDKING Professional











































Отзывы:

Нет отзывов