background image

3

Subject to change without notice  |  83059200dUK – Translation of the original operating manual |  ait-deutschland GmbH

1  About this operating manual

This operating manual is part of the unit.

 

Before working on or with the unit, read the 

operating manual carefully and follow it for all 

activities at all times, especially the warnings and 

safety instructions.

 

Keep the operating manual to hand at the unit 

and pass on to the new owner if the unit changes 

hands.

 

If you have any questions or anything is unclear, 

ask the manufacturer’s local partner or the 

factory’s customer service.

 

Note and follow all reference documents.

1.1  Validity

This operating manual refers solely to the unit identified 

by the nameplate and device label (see “Nameplate” 

and “Drill-hold pattern” on page 19).

1.2  Reference documents

The following documents contain additional 

information with regard to this operating manual:

 

Planning & design manual, hydraulic integration

 

Operating manual of the heating and heat pump 

controller

 

Brief description of the heat pump controller

 

Operating manual of the expansion board 

(accessories)

 

Log book

 

Heat pump manual

1.3  Symbols and markings

Identification of warnings

Symbol

Meaning

Safety-relevant information. 

Warning of physical injuries.

DANGER

Indicates imminent danger resulting 

in severe injuries or death.

WARNING

Indicates a potentially dangerous 

situation, which can result in severe 

injuries or death.

CAUTION

Indicates a potentially dangerous 

situation, which can result in 

moderate or minor injuries.

ATTENTION

Indicates a potentially dangerous 

situation, which can result in 

property damage.

Symbols in the document

Symbol

Meaning

Information for qualified personnel

Information for the owner/operator

Requirement for action

Single step action prompt

1., 2., 3., …

Numbered step within a multi-step 

action prompt. Keep to the given 

order.
Additional information, e.g. a tip on 

making work easier, information on 

standards

 

Reference to further information 

elsewhere in the operating manual 

or in another document

 

 

Listing

Содержание HDV 12-3

































Отзывы: