manualshive.com logo in svg

Airxcel Marvair VAIVA36, Руководство по техническому обслуживанию и ремонту, Страница: 15 / 75

Поделиться
Скачать
Airxcel Marvair VAIVA36 Скачать руководство пользователя страница 15

15 

Scholar V VAIVA Maintenance & Service Manual 10/2017 Rev.2

•  Channel 0

 – 

Supply Air (treated air discharged from unit to the room)

• Supply air temperature information

• Used to control hot gas reheat

SUPPLY AIR THERMOCOUPLE SENSOR 

(Located behind plenum grille)

•  Channel 1

 – 

Outdoor Air (ambient outdoor air entering condenser compartment)

• Supply air temperature information

• Used to switch heat pump off and electric resistance on if outdoor air gets 

too cold for satisfactory heat pump heating

OUTDOOR TEMPERATURE 

SENSOR

•  Channel 2, 3

 – 

Outdoor Coil #1 & #2: T

his thermocouple is located in the 

distributor tube bundle for Coils #1 & #2 and measures refrigerant temperature.

• Used to control defrost in heating mode

• Used to control condenser fan cycling in cooling mode

OUTSIDE COIL #1

(Embedded in the 

distributor tubes)

OUTSIDE COIL #2

(Embedded in the 

distributor tubes)

OUTDOOR COIL

THERMOCOUPLE

F. Variable Speed Control Methodology 

The variable speed compressor is capable of operating at speed from 1200 rpm 

to 3600 rpm in cooling and 4800 rpm in heating. Cooling or heating capacity is 

basically proportional to the compressor speed. All limits are programmable.
A control band is established by assigning a differential (+ or -) to the cooling set 

point or heating set point. This differential is adjustable but comes factory set at 

0.25°F. For example, if the cooling setpoint is 75°F, the differential establishes 

a “deadband” from 74.75°F to 75.25 °F. If the heating setpoint is 65°F, the 

“deadband” would be 64.75 °F to 65.25 °F.
In Cooling, if the room temperature is outside of this deadband on the high side, 

the compressor speed (and cooling capacity) slowly ramps up. This cools the 

room more and lowers the room temperature. When the room temperatures 

enters the “deadband”, the compressor speed and capacity stop modulating and 

hold constant at their established values. If the room temperature falls below the 

“deadband” on the low side, the compressor speed and capacity slowly ramp 

down until the room temperature climbs and re-enters the “deadband”, at which 

point the compressor speed and capacity stop modulating and hold constant at 

their established values. The following drawing shows this process in graphical 

form.

Содержание Marvair VAIVA36












































































Отзывы:

Нет отзывов