background image

16

9. Installation

9.1 Installation procedures

If the air conditioner is transferred to a new user, this manual shall be transferred to the user, together with the

conditioner.

Before installation, be sure to read Safety Considerations in this manual for proper installation.

The safety considerations stated below is divided into " WARNING" and "  ATTENTION". The matters on

severe accidents caused from wrong installation, which is likely to lead to death or serious injury, are listed in

" WARNING". However, the matters listed in "  ATTENTION" are also likely cause the severe accidents. In

general, both of them are the important items related to the security, which should be strictly abided by.

After the installation, perform test run to make sure everything is in normal conditions, and then operate and

maintain the air conditioner in accordance with the User Manual. The User Manual should be delivered to the

user for proper keeping.

■ Please ask the special maintenance station for installation and repair. Water leakage, electric shocks or fire

accidents might be caused from improper installation if you conduct the installation by your own.

■ The installation should be conducted properly according to this manual. Water leakage, electric shocks or fire

accidents might be caused from improper installation.

Please make sure to install the air conditioner on the place where can bear the weight of the air conditioner. The

air conditioner can't be installed on the grids such as the non-special metal burglar-proof net. The place with

insufficient support strength might cause the dropdown of the machine, which may lead to personal injuries.

The installation should be ensured against typhoons and earthquakes, etc. The installation unconformable to the

requirements will lead to accidents due to the turnover of the machine.

■ Specific cables should be used for reliable connections of the wirings. Please fix the terminal connections reliably

to avoid the outside force applied on the cables from being impressed on the cables. Improper connections and

fixings might lead to such accidents as heating or fire accidents.

Correct shapes of wirings should be kept while the embossed shape is not allowed. The wirings should be reliably

connected to avoid the cover and the plate of the electrical cabinet lipping the wiring. Improper installation might

cause such accidents as heating or fire accidents.

■ While placing or reinstalling the air conditioner, except the specific refrigerant (R410A), don't let the air go into the

refrigeration cycle system. The air in the refrigeration cycle system might lead to the cracking or personal injuries

due to abnormal high pressure of the refrigeration cycle system.

■ During installation, please use the accompanied spare parts or specific parts. If not, water leakage, electric

shocks, fire accidents or refrigerant leakage might be caused.

Don't drain the water from the drainpipe to the waterspout where may exist harmful gases such as sulfureted gas

to avoid the harmful gases entering into the room.

During installation, if refrigerant leakage occurs, ventilation measures should be taken, for the refrigerant gas

might generate harmful gases upon contacting the flame.

After installation, check if any refrigerant leakage exists. If the refrigerant gas leaks in the room, such things as air

blowing heaters and stoves, etc. may generate harmful gases.

■ Don't install the air conditioner at the places where the flammable gases may leak. In case the gas leakage

occurs around the machine, such accidents as fire disasters may be caused.

The drainpipe should be properly mounted according to this manual as to ensure the smooth drainage. In

addition, heat preservation should be taken to avoid condensation. Improper drainpipe mounting might cause

water leakage, which will get the articles at home wet.

The refrigerant gas pipe and liquid pipe should be heat insulated to preserve heat. For inappropriate heat

insulation, the water caused from the condensation will drop to get the article at home wet.

■ If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified

persons in order to avoid a hazard.

This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental

capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction

concerning use of the appliance by a person responsible for their safety.

Children should be supervised to ensure that they do not play with the appliance.

WARNING

Содержание AWSI-CFV007-N11























































Отзывы: