Airspan FlexNET ASN-700 Скачать руководство пользователя страница 19

Страница: 19 / 76

605-0001-801 FlexNET Link Products

NAVIGATING THE CONFIGURATION MENU

Use the configuration menu on the left of the screen (see Figure 3), to access the other pages of

the configuration utility. Clicking on one of the menu entries will open a sub-menu containing

links to further configuration pages.

Figure 3

The configuration menu

HOME

The first page displayed at login, containing a summary of information about the ASN-700/800

and its configuration. See Figure 2 on page 11.

GENERAL

Contains general information about your ASN-700/800. See Figure 6 on page 15.

ASSOCIATIONS

Lists additional devices connected to your WLAN. See Figure 8 on page 16.

NETWORKING

Advanced options for configuring the Ethernet and radio interfaces of the ASN-700/800. Refer to

page 17.

SECURITY

Add and remove administrators, and change administrator passwords. Refer to page 25.

SERVICES

Set up network services, such as DHCP. Refer to page 27.

UTILITIES

Network utilities to test the connectivity of your network. Refer to page 33.

SOFTWARE

Update your ASN-700/800 with the latest firmware. Refer to page 36.

LOG

Edit and examine the ASN-700/800 activity log. Refer to page 38.

Saving and committing changes

The two action buttons OK and Commit Settings are used to implement or undo changes to

the configuration of the ASN-700/800.

Figure 4

The action buttons

Содержание FlexNET ASN-700













































































Результаты поиска

Содержание FlexNET ASN-700

Отзывы:

Похожие инструкции для FlexNET ASN-700

Бренды по названию

Популярные бренды

Airspan FlexNET ASN-700, Руководство пользователя

Результаты поиска

Содержание FlexNET ASN-700

Отзывы:

Похожие инструкции для FlexNET ASN-700

Бренды по названию

Популярные бренды