Airspan FlexNET ASN-700 Скачать руководство пользователя страница 39

Страница: 39 / 76

605-0001-801 FlexNET Link Products

UTILITIES

During configuration of your wireless network, you may wish to test the status and connectivity

of nodes. The configuration system of the ASN-700/800 comes with a set of useful features;

ability to view the current state of the unit’s ARP Table and Ping & Traceroute testing tools. To

access these features, click on the UTILITIES link in the configuration menu.

Figure 23

The Utilities menu

ARP table

A table of the most recent IP-to-physical address bindings.

Viewing the ARP table

The ARP (Address Resolution Protocol) table lists the most recently acquired associations

between MAC (physical-layer) addresses and IP addresses on the network. Click on the link

UTILITIES>Arp Table to view the most recent ARP table.

Figure 24

The ARP table

Locally connected hosts are displayed as rows in the table. The table's columns provide

information about each host:

Address

The IP address of a host.

Содержание FlexNET ASN-700













































































Результаты поиска

Содержание FlexNET ASN-700

Отзывы:

Похожие инструкции для FlexNET ASN-700

Бренды по названию

Популярные бренды

Airspan FlexNET ASN-700, Руководство пользователя

Результаты поиска

Содержание FlexNET ASN-700

Отзывы:

Похожие инструкции для FlexNET ASN-700

Бренды по названию

Популярные бренды