Airspan FlexNET ASN-700 Скачать руководство пользователя страница 21

Страница: 21 / 76

605-0001-801 FlexNET Link Products

GENERAL

The general screen presents common information about your ASN-700/800.

Figure 5

The General link

Click on the GENERAL link to view and set the following information of the ASN-700/800 base
station unit (see Figure 6):

GENERAL SETTINGS

Contains the name, location and coordinates of your base station unit.

TIME ZONE

The correct time zone should be set here.

SYSTEM TIME

Enter the correct time and date here and click Set.

NETWORK TIME PROTOCOL

If you wish to synchronize the system time with a time server, click Enabled and enter the IP

address of the server you want to you use.

Figure 6

The General screen

Note: Remember to click on the OK button to apply your changes, and click Commit

Settings to permanently accept the new configuration.

Содержание FlexNET ASN-700













































































Результаты поиска

Содержание FlexNET ASN-700

Отзывы:

Похожие инструкции для FlexNET ASN-700

Бренды по названию

Популярные бренды

Airspan FlexNET ASN-700, Руководство пользователя

Результаты поиска

Содержание FlexNET ASN-700

Отзывы:

Похожие инструкции для FlexNET ASN-700

Бренды по названию

Популярные бренды