manualshive.com logo in svg

Airspan AirHarmony 4000 DC, Руководство по установке

Поделиться
Скачать
Airspan AirHarmony 4000 DC Скачать руководство пользователя страница 42

AirHarmony-4000 DC (Integrated External Duplexers) Installation Guide 

UGD-D01123

 

Airspan Commercial and Internal Use 

36 

Caution:

 Power down AirHarmony prior to disconnecting antenna. 

 

2.

 

Weather-proof the RF connections. 

Note:

 The above is also applicable for replacement assembly.  

5.2.2

 

Weather-proofing the Antenna Connections 

Weather-proofing of all the connections is required. This is done with a layer of self-amalgamating 
tape followed by an over layer of PVC tape. The weather-proofing is best done at this stage to give 
easier access to the connections. 

Note:

 Weather-proofing is best done at the assembly stage to give easier access to the 

connections. Weather-proofing is to be done to all RF connectors. 

 

Verify the RF connectors are completely weather-proof. 

5.3

 

Cable Connections 

Note:

 The following images are for illustration purposes only. The actual tools or 

hardware may differ according to manufacturer. 

5.3.1

 

Copper Ethernet Cable Assembly 

The following demonstrates the recommended assembly instructions, hardware and tool 
requirements for the proper Ethernet cable assembly of the Ethernet Category 5e (enhanced) 
(CAT5e) cable used by Airspan products.  

The Ethernet cable is connected using a standard RJ45 connector protected by a harsh environment 
protective casing. 

Hardware Requirements 

The following are the cable and connectors available from Airspan. 

 

Table 11: Cable Hardware 

Airspan Part Number 

Description  

CAT5e-STP-305M-R 

CAT5e Ethernet Cable, 305M (1000ft), STP, Reel 

RJ45-ETH-SHLD-CONN 

RJ45 Ethernet Connector, Shielded 

 

Assembly Instructions 

The Copper Ethernet cable is connected to the AirHarmony-1000 using a Gland connector assembled 
on the bottom panel of the unit, as shown below. 

 

Figure 19: Gland connector - copper 

Содержание AirHarmony 4000 DC



















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды