manualshive.com logo in svg

Airspan AirHarmony 4000 DC, Руководство по установке

Поделиться
Скачать
Airspan AirHarmony 4000 DC Скачать руководство пользователя страница 41

AirHarmony-4000 DC (Integrated External Duplexers) Installation Guide 

UGD-D01123

 

Airspan Commercial and Internal Use 

35 

5

 

AirHarmony-4000 DC INT EXT Connections 

This section describes Grounding procedure, cable preparation and connections and external 
antenna assembly. 

5.1

 

Grounding 

The AirHarmony-4000 DC INT EXT requires a secure ground connection. The ground cable should be 
connected with a grounding screw fitted with a flat washer and lock washer to the bottom of the 
chassis clearly marked with the universal ground symbol as shown below. The grounding screw (M6 
x 16) is pre-installed during assembly. 

 

Figure 18: Grounding 

 

 

 

 

 

 

 

The cable should be grounded and bonded according to international or local standards. 

5.2

 

Remote Antenna Assembly 

 

The AirHarmony-4000 DC INT EXT unit is be used with a remotely attached antenna. 

Fo  i stallatio  of a  e otel   ou ted a te a follo  the a te a  a ufa tu e ’s i st u tio s a d 

connect the antenna to the AirHarmony-4000 

I teg ated E te al Duple e s’ RF  o e to s  fe ale 

DIN 4.1/9.5 connector) using the appropriate cables with a male DIN 4.1/9.5 connector. 

Caution:

 Take care not over tighten the RF connector. The connector nut should be 

tightened to a nominal torque of no more than 2.0 Nm (1.47 lb-ft). RF failures can result 
when the RF connector is over-tightened. 

5.2.1

 

Connecting RF Jumper Cables to External Antenna 

The following describes how to connect the antenna cables to the Integrated Duplexers. 

1.

 

Attach, connect and secure the RF cable between the external antenna and the 
appropriate RF connection on the top of the Integrated Duplexers. 

Caution:

 Antennas must be connected and attached before AirHarmony is powered on. 

 

Содержание AirHarmony 4000 DC



















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды