40
You can activate continuous heating by setting the
heating cycle to 60 minutes.
1. START THE HEATER
2. SELECT TIMER OPERATION
Select timer operation by pressing the MODE button. The
timer operation light is lit after pressing mode button.
3. When timer operation is on, a light ring is shown on the
left. The set operating time (in minutes) is displayed on the
right. Select the desired operating time with the arrow
buttons. The selected time flashes on the display. If the
arrow buttons are not pressed for three (3) seconds, the
time setting shown on the screen is activated.
4. The operating time can be set between 10 and 55
minutes, or the heater can be set to run continuously. Once
the operating cycle ends, the heater always suspends
operation for five (5) minutes. Two lines (- -) are shown on the
display alongside the operating time to indicate the pause.
Timer operation can be used to operate the heater in intervals. The operating time can be set between 10 and 55
minutes. The pause between cycles is always five minutes. The heater can also be set to be continuously on. In timer
operation, the heater does not take the thermostat’s temperature or the set temperature into account.
Heating 20 min
Heating 20 min
Heating 20 min
Pause 5 min
Start
Pause 5 min
Continuous heating
display The heater is
now operating
continuously.
The display indicates a
20-min heating cycle.
OPERATING INSTRUCTIONS
TIMER OPERATION
10
HOW TO USE
TIME CONTROL
Repetition time cycle can be set from 10min. to 55min.
1. Push power button.
2. By pushing mode button, please select
time control mode. At that time, time control
lamp is lighten.
the time is blinking, and if you don't push
button for 3sec., this displayed blinking time is
set as 'repetition time'. At that time, the former
repetition time is automatically erased.
4. At the operation mode, the operation symbol and
repetition time both are displayed, and when you
make off by pushing power button, STOP symbol
‘Interval pause time’, STOP symbol (--) and
repetition time both displayed.
5. The repitition time can be set from 10min. to 55min. The operation is as much as setting time, and
'Constant opeartion'. This means, without pause, the operation is constantly made.
Operation for 20min.
Operation for 20min.
Operation for 20min.
Stop for 5min
.
Start
Stop for 5min.
Constant
operation status
In case of setting the
repetition time as 20min.
Repetition time 20
means, every 20min.
Operation and 5min.
Pause
10
HOW TO USE
TIME CONTROL
Repetition time cycle can be set from 10min. to 55min.
1. Push power button.
2. By pushing mode button, please select
time control mode. At that time, time control
lamp is lighten.
the time is blinking, and if you don't push
button for 3sec., this displayed blinking time is
set as 'repetition time'. At that time, the former
repetition time is automatically erased.
4. At the operation mode, the operation symbol and
repetition time both are displayed, and when you
make off by pushing power button, STOP symbol
‘Interval pause time’, STOP symbol (--) and
repetition time both displayed.
5. The repitition time can be set from 10min. to 55min. The operation is as much as setting time, and
'Constant opeartion'. This means, without pause, the operation is constantly made.
Operation for 20min.
Operation for 20min.
Operation for 20min.
Stop for 5min
.
Start
Stop for 5min.
Constant
operation status
In case of setting the
repetition time as 20min.
Repetition time 20
means, every 20min.
Operation and 5min.
Pause
10
HOW TO USE
TIME CONTROL
Repetition time cycle can be set from 10min. to 55min.
1. Push power button.
2. By pushing mode button, please select
time control mode. At that time, time control
lamp is lighten.
the time is blinking, and if you don't push
button for 3sec., this displayed blinking time is
set as 'repetition time'. At that time, the former
repetition time is automatically erased.
4. At the operation mode, the operation symbol and
repetition time both are displayed, and when you
make off by pushing power button, STOP symbol
‘Interval pause time’, STOP symbol (--) and
repetition time both displayed.
5. The repitition time can be set from 10min. to 55min. The operation is as much as setting time, and
'Constant opeartion'. This means, without pause, the operation is constantly made.
Operation for 20min.
Operation for 20min.
Operation for 20min.
Stop for 5min
.
Start
Stop for 5min.
Constant
operation status
In case of setting the
repetition time as 20min.
Repetition time 20
means, every 20min.
Operation and 5min.
Pause
10
HOW TO USE
TIME CONTROL
Repetition time cycle can be set from 10min. to 55min.
1. Push power button.
2. By pushing mode button, please select
time control mode. At that time, time control
lamp is lighten.
the time is blinking, and if you don't push
button for 3sec., this displayed blinking time is
set as 'repetition time'. At that time, the former
repetition time is automatically erased.
4. At the operation mode, the operation symbol and
repetition time both are displayed, and when you
make off by pushing power button, STOP symbol
‘Interval pause time’, STOP symbol (--) and
repetition time both displayed.
5. The repitition time can be set from 10min. to 55min. The operation is as much as setting time, and
'Constant opeartion'. This means, without pause, the operation is constantly made.
Operation for 20min.
Operation for 20min.
Operation for 20min.
Stop for 5min
.
Start
Stop for 5min.
Constant
operation status
In case of setting the
repetition time as 20min.
Repetition time 20
means, every 20min.
Operation and 5min.
Pause
10
HOW TO USE
TIME CONTROL
Repetition time cycle can be set from 10min. to 55min.
1. Push power button.
2. By pushing mode button, please select
time control mode. At that time, time control
lamp is lighten.
the time is blinking, and if you don't push
button for 3sec., this displayed blinking time is
set as 'repetition time'. At that time, the former
repetition time is automatically erased.
4. At the operation mode, the operation symbol and
repetition time both are displayed, and when you
make off by pushing power button, STOP symbol
‘Interval pause time’, STOP symbol (--) and
repetition time both displayed.
5. The repitition time can be set from 10min. to 55min. The operation is as much as setting time, and
'Constant opeartion'. This means, without pause, the operation is constantly made.
Operation for 20min.
Operation for 20min.
Operation for 20min.
Stop for 5min
.
Start
Stop for 5min.
Constant
operation status
In case of setting the
repetition time as 20min.
Repetition time 20
means, every 20min.
Operation and 5min.
Pause
10
HOW TO USE
TIME CONTROL
Repetition time cycle can be set from 10min. to 55min.
1. Push power button.
2. By pushing mode button, please select
time control mode. At that time, time control
lamp is lighten.
the time is blinking, and if you don't push
button for 3sec., this displayed blinking time is
set as 'repetition time'. At that time, the former
repetition time is automatically erased.
4. At the operation mode, the operation symbol and
repetition time both are displayed, and when you
make off by pushing power button, STOP symbol
‘Interval pause time’, STOP symbol (--) and
repetition time both displayed.
5. The repitition time can be set from 10min. to 55min. The operation is as much as setting time, and
'Constant opeartion'. This means, without pause, the operation is constantly made.
Operation for 20min.
Operation for 20min.
Operation for 20min.
Stop for 5min
.
Start
Stop for 5min.
Constant
operation status
In case of setting the
repetition time as 20min.
Repetition time 20
means, every 20min.
Operation and 5min.
Pause
5 min pause, display
