Airmar DX900+ Скачать руководство пользователя страница 8

8

WARNING

: A safe installation requires a 0.5 amp fast-blow fuse or circuit

breaker.

WARNING

: The power supply voltage must be 9 - 16 VDC.

CAUTION

: The sensor is NOT compatible with a bronze housing, because

bronze may cause interference resulting in incorrect readings.

CAUTION

: Never pull, carry, or hold the sensor by its cable; this may sever

internal connections.

CAUTION

Plastic housing

—Never use a fairing with a plastic housing;

the protruding sensor would be vulnerable to damage from impact.

CAUTION

Metal housing

—Never install a metal housing in a vessel with

a positive ground system.

CAUTION

Stainless steel housing in a metal hull

—Stainless steel

housing must be isolated from a metal hull to prevent electrolytic corrosion.
Use the isolation bushing supplied.

CAUTION

: The sensor must be aligned within 1° of parallel to the

centerline/keel of the boat.

CAUTION

: The arrow on the top of the insert must point forward toward

the bow area to align with the water flow.

CAUTION

: The bottom of the insert must be flush with the bottom of the

housing. Note that the electrodes will protrude into the water.

CAUTION

: Do not paint the face of the insert with the electrodes.

CAUTION

: The sensor must be in good contact with the water at all times.

CAUTION

: Never use solvents. Cleaner, fuel, sealant, paint, and other

products may contain solvents that can damage plastic parts, especially the
insert’s face.

IMPORTANT

: Please read the Owner’s Guide completely before

proceeding. These instructions supersede any other instructions in your
instrument manual if they differ.

Содержание DX900+

























Отзывы: