Airmar DX900+ Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 24

Airmar DX900+ Скачать руководство пользователя страница 4

4

Introduction

Thank you for purchasing Airmar’s Electromagnetic MultiLog Sensor. The
DX900+ is the industry’s first Bluetooth

®

-enabled, multi-functional unit. It is

actually several sensors in a single housing. And it is the only sensor that truly
measures leeway instantaneously—not derived from a calculation. Data is output
in NMEA 0183 or NMEA 2000

®

format.

Features & Options

• Bluetooth

®

-enabled to connect your boat display and smart devices

• Supports both iOS and Android platforms
• Performs speed calibration and more through the CAST

™

app

• Configurable data update rate: up to 10Hz
• Diagnostic information for troubleshooting
• Interface to update firmware
• Dual-axis, electromagnetic, speed sensor
• Fast-response water temperature
• Depth transducer
• Three-axis accelerometer
• Three-axis rate gyroscope
• Retrofits most existing 51mm (2") thru-hull housings

Functions & Outputs

DX900+

Speed

Leeway

Reverse speed

Temperature of water

Depth of water

Optional

Heel & Trim

Optional

NMEA 0183: RS422

Optional

NMEA 0183: RS232

Optional

NMEA 2000: CAN

Optional

«
...
2
3
4
5
6
...
»

Содержание DX900+

























Отзывы:

Нет отзывов