Airmar DX900+ Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 24

Airmar DX900+ Скачать руководство пользователя страница 6

6

Applications

• High-speed racing sailboats
• Not recommended for boats designed to pull air under the hull.
•

Plastic

housing recommended for fiberglass or metal hull only.

Never install a plastic housing in a wood hull, since swelling of the wood can
possibly fracture the plastic

.

•

Stainless steel

housing compatible with all hull materials.

Recommended for aluminum hulls to prevent electrolytic corrosion

provided the

stainless steel housing is isolated from the metal hull.

• Accommodates a deadrise angle up to 22°.

Tools & Materials

Safety glasses
Dust mask
Ear protection
Water-based anti-fouling paint (

mandatory in salt water

)

Electric drill with 10mm (3/8")

or

larger chuck capacity

Drill bit:

3mm

or

1/8"

Hole saw:

Plastic/metal housing in non-metal hull 51mm

or

2"

Stainless steel housing in metal hull

57mm

or

2-1/4"

Sandpaper
Mild household detergent

or

weak solvent (such as alcohol)

File (installation in a metal hull)
Marine sealant (suitable for below waterline)
Measuring tape
Chalk line
Slip-joint pliers (installing a metal housing)
Installation in a cored fiberglass hull (page 17):

Hole saw for hull interior:

60mm

or

2-3/8"

Fiberglass cloth and resin

or

Cylinder, wax, tape, and casting epoxy

Device-net cable [maximum 2m (6')] (NMEA 2000)
Pencil
Cutting pliers
Phillips screwdriver
Wire strippers
Heat-shrink tubing
Heat gun
Blade screwdrivers
Wrench

«
...
4
5
6
7
8
...
»

Содержание DX900+

























Отзывы:

Нет отзывов