manualshive.com logo in svg

Airmar Technology Corporation TDT1000, Руководство пользователя, Страница: 16 / 17

Поделиться
Скачать
Airmar Technology Corporation TDT1000 Скачать руководство пользователя страница 16

Troubleshooting

TDT1000 will not turn on

• Is the unit fully charged?
• Confirm that the Charging light is lit.
• It may take a full charging cycle before the unit will power on.

Replacement Parts

Lost, broken, or worn parts should be replaced immediately.

Part

Part Number

TDT1000 Kit

33-762-01

AC-DC Power Adapter Kit

33-739-01

Power charger with USB to micro USB connectors
International wall-plug adapters for UK, Australia, and Europe

Test Block: small

33-758-01

Test Block: large

33-759-01

Test Cable with breakout box for transducers with NO connector

33-736-01

Carrying Case

ACC-TDT1000-CASE

Quick Start Guide

17-632-01

Owner’s Guide can be found at www.airmar.com/tdt1000.

17-615-01

SensorCheck™ app guide can be found at www.airmar.com/tdt1000.

17-615-02

Customer Service

For training and support, contact Airmar Technical Support at [email protected].

Gemeco 

USA
Tel: 803.693.0777
email: [email protected]

Airmar EMEA

Europe, Middle East, Africa
Tel: +33.(0)2.23.52.06.48
email: [email protected]

Trademarks

Airmar

®

 is a registered trademark of Airmar Technology Corporation.

 

K-Y

®

 is a registered trademark of 

Reckitt Benckiser Group plc.

SensorCheck™ is a trademark of Airmar Technology Corporation.

16

Содержание TDT1000


















Отзывы:

Нет отзывов